Replacing the water filter in your Kenmore refrigerator is a simple task that can be completed in a few minutes. This will ensure clean, fresh-tasting water from your refrigerator’s dispenser. A clogged filter can cause a decrease in water flow, a strange taste in your water, or even ice buildup in the ice maker. Changing the filter regularly will help prevent these problems and keep your refrigerator running efficiently.
Before you begin, locate the water filter. It is typically found in the upper right corner of the fresh food compartment, behind the top shelf. Once you have located the filter, turn off the water supply to your refrigerator. There is usually a small valve located behind the refrigerator that you can turn off. Once the water supply is turned off, depress the eject button on the filter housing and pull the filter straight down to remove it. Then, remove the new filter from its packaging and insert it into the housing. Push up on the filter until it clicks into place. Finally, turn the water supply back on and run water through the dispenser for a few minutes to flush out any remaining air.
Changing the water filter in your Kenmore refrigerator is a quick and easy task that can be completed in a few minutes. By following these simple steps, you can ensure that your refrigerator is dispensing clean, fresh-tasting water.
Identifying the Water Filter Location
Locating the water filter in your Kenmore refrigerator is crucial for ensuring a steady supply of clean, filtered water. The filter’s placement varies depending on the specific refrigerator model.
Front-Mounted Filters
Many Kenmore refrigerators feature front-mounted water filters, located on the bottom or middle grille at the front of the unit. To identify this type of filter:
- Inspect the bottom or middle grille of your refrigerator for a small, circular opening.
- If you see a plastic knob or indentation near the opening, gently pull or press it to release the filter cartridge.
- Once the cartridge is out, check its packaging or the user manual for the specific model number and replacement instructions.
Rear-Mounted Filters
Some Kenmore refrigerators, particularly side-by-side or French door models, have rear-mounted water filters. To locate this type of filter:
- Locate the panel covering the back of the refrigerator compartment (usually at the top).
- Remove the panel by unscrewing any screws or clips holding it in place.
- Behind the panel, you should see the water filter cartridge inside a housing or bracket.
- Check the packaging or user manual for the specific model number and replacement instructions.
Type | Location |
---|---|
Front-Mounted | Bottom or middle grille at the front |
Rear-Mounted | Behind the panel covering the back of the refrigerator compartment |
Gathering the Necessary Tools
To replace the water filter in your Kenmore refrigerator, you will need the following tools:
- A new Kenmore water filter (model number 46-9990)
- A bucket or bowl (to catch any water that may leak out)
- A clean cloth or paper towels (to wipe up any spills)
- A Phillips head screwdriver (optional)
Choosing the Right Water Filter
The Kenmore 46-9990 water filter is the only filter that is compatible with all Kenmore refrigerators. It is important to use the correct filter to ensure that your refrigerator is functioning properly.
Location of the Water Filter
The water filter is typically located in the lower right-hand corner of the refrigerator, behind the grill. To access the filter, you will need to remove the grill by gently pulling it up and away from the refrigerator.
Tools for Removing the Old Filter
Once you have located the water filter, you will need to use a Phillips head screwdriver to remove the screws that hold it in place. Be careful not to overtighten the screws when you replace the new filter.
Safety Precautions
Before you begin working on your refrigerator, it is important to unplug it from the electrical outlet. This will help to prevent you from getting shocked. You should also turn off the water supply to the refrigerator to prevent water from leaking out when you remove the old filter.
Shutting Off the Water Supply
Before you begin changing the water filter, it’s essential to shut off the water supply to avoid any unexpected leaks or spills. Here’s a step-by-step guide to help you do it:
- Locate the water supply valve: This valve is typically located behind or underneath the refrigerator, near the inlet hose. It may have a small handle or knob that you can turn.
- Turn off the valve: If the valve has a handle, turn it clockwise to close it. If it has a knob, turn it to the “off” position.
- Drain the remaining water in the line: To ensure that there is no water left in the line that could leak out while changing the filter, open the water dispenser or faucet on the refrigerator to release the remaining water. Let it drain until no more water comes out.
Additional Tips for Shutting Off the Water Supply
* If you can’t locate the water supply valve, refer to your refrigerator’s user manual for specific instructions.
* If the valve is difficult to turn, use a wrench to gently tighten it, but do not overtighten it.
* If you experience any leaks or damage while shutting off the water supply, contact a qualified plumber immediately.
Removing the Old Filter
Locate the water filter housing. It is typically found in the refrigerator compartment or behind the grille at the bottom of the refrigerator.
Turn off the water supply to the refrigerator. This is usually done by closing the water valve that is located near the water filter housing.
Unpack the new water filter and remove the protective cap from the ends of the filter.
Hold the release button on the water filter housing and pull the old filter straight down to remove it.
The old water filter will contain residual water, so be careful not to spill it.
Dispose of the old water filter properly.
Installing the New Filter
Once you have located the old filter, it’s time to replace it with a new one. Here’s a detailed step-by-step guide:
-
Close the Water Supply Valve: Turn off the water supply valve located near the refrigerator. This will prevent water from leaking during the filter change.
-
Relieve Water Pressure: Press the water dispenser button for a few seconds to release any residual water pressure in the lines.
-
Disconnect the Old Filter: Grip the old filter and gently twist it counterclockwise to disconnect it from the housing. Do not use excessive force.
-
Prepare the New Filter: Remove the new filter from its packaging and soak it in cold water for about 2-3 minutes. This helps activate the filter media.
-
Insert the New Filter: Insert the new filter into the housing by aligning the notch on the filter with the corresponding notch in the housing. Push the filter up and twist it clockwise until it clicks into place. Avoid overtightening.
Table: Key Points for Installing the New Filter
Step | Key Point |
---|---|
1 | Close the water supply valve. |
2 | Relieve water pressure by pressing the water dispenser. |
3 | Disconnect the old filter by twisting counterclockwise. |
4 | Soak the new filter in water for activation. |
5 | Align the filter notch with the housing notch and twist clockwise to secure it. |
Resetting the Filter Indicator
Once you have successfully replaced the water filter, it’s important to reset the filter indicator so that it can accurately track the remaining lifespan of the new filter. Here’s a step-by-step guide on how to reset the filter indicator on your Kenmore refrigerator:
- Locate the Filter Indicator: The filter indicator is typically located on the refrigerator’s control panel or dispenser. It may be a small light or an icon that displays the filter’s status.
- Press and Hold the Button: Find the button or combination of buttons that is used to reset the filter indicator. This may vary depending on your specific Kenmore model. Refer to your user manual or look for labels on the control panel.
- Hold for the Specified Duration: Press and hold the designated button or buttons for the amount of time specified in your user manual. This is typically around 5-10 seconds.
- Release the Button: Once the required time has elapsed, release the button. The filter indicator should now be reset and display the status of the new filter.
- Check the Indicator: After resetting the filter indicator, make sure that it correctly indicates the new filter as “good” or “OK.” If the indicator still shows “replace” or “bad,” repeat the reset process.
- Set the Filter Life: Some Kenmore refrigerators allow you to set the lifespan of the new filter. This helps the indicator provide accurate reminders for future filter replacements. Refer to your user manual to find the instructions on how to set the filter life.
Troubleshooting Common Issues
If you encounter any issues while changing the water filter on your Kenmore refrigerator, refer to the following troubleshooting tips:
1. Water Still Dispensing
Ensure the new filter is securely tightened by hand. If it’s overtightened, it may crack or leak. If it’s not tight enough, water may leak. Check for any debris or particles blocking the filter’s outlet or inlet.
2. Water Discolored
If the water coming out is discolored, run the water through the dispenser for a few minutes. This will flush out any trapped air or debris. If the water remains discolored, replace the filter or contact a qualified technician.
3. Low Water Pressure
Low water pressure can be caused by clogged filters or lines. Replace the filter and check for any obstructions in the water lines.
4. Water Filter Not Disconnected
Before removing the old filter, ensure the water supply has been disconnected. This will prevent water from leaking on the floor.
5. Water Filter Stuck
If the filter is stuck, use a filter wrench or pliers to gently loosen it. Do not apply excessive force, as it may damage the filter or the refrigerator.
6. Water Leakage
If water leaks from the filter, ensure it is properly seated and tightened. Check for any cracks or damage to the filter. If the leak persists, replace the filter.
7. Reset Water Filter Indicator
Some Kenmore refrigerators have a water filter indicator that needs to be reset after changing the filter. To reset the indicator:
- Locate the “Filter Indicator” button on the dispenser or control panel.
- Press and hold the button for 3-5 seconds until the indicator light changes color or resets.
- Refer to your Kenmore refrigerator manual for specific instructions on resetting the filter indicator.
Maintenance Tips for Optimal Performance
1. Replace the Water Filter Regularly
Refer to your refrigerator’s user manual for the recommended replacement schedule. As a general rule, filters should be replaced every six months or according to the manufacturer’s instructions.
2. Clean the Water Dispenser
Wipe down the exterior of the water dispenser with a damp cloth. Avoid using harsh chemicals or abrasives.
3. Flush the Water Lines
Periodically, run water through the dispenser for a few minutes to clear out any built-up sediment or impurities.
4. Clean the Ice Maker
If your refrigerator has an ice maker, clean it according to the manufacturer’s instructions. This will help prevent ice buildup and ensure that the ice cubes are clean and free from odors.
5. Keep the Refrigerator Clean
Wipe down the interior and exterior of the refrigerator regularly to prevent the buildup of spills, crumbs, and other debris.
6. Unplug the Refrigerator During Extended Absences
If you will be away from home for an extended period, unplug the refrigerator to conserve energy and prevent potential damage.
7. Check the Door Gaskets
Inspect the door gaskets regularly to ensure that they are not torn or cracked. If the gaskets are damaged, they can allow cold air to escape, leading to energy loss and reduced cooling efficiency.
8. Avoid Overcrowding the Refrigerator
Overcrowding the refrigerator can restrict airflow, hindering the cooling process. Ensure that there is adequate space around food items to allow air to circulate freely.
Benefits of Regularly Changing the Water Filter
Regularly changing the water filter in your Kenmore refrigerator provides numerous benefits:
Improved Water Taste and Odor
A fresh filter removes impurities and contaminants from your water, resulting in noticeably better-tasting and odor-free drinking water. You’ll enjoy refreshing and flavorful beverages every time.
Enhanced Ice Quality
A clean filter produces clearer and purer ice cubes, free from chlorine taste and unpleasant odors. Your ice will be more aesthetically pleasing and enhance the enjoyment of your cold drinks.
Reduced Sediment Buildup
Over time, sediment can accumulate in your refrigerator’s water lines and appliances. A new filter effectively traps these particles, preventing them from clogging and compromising the performance of your refrigerator.
Extended Appliance Life
By removing impurities and reducing sediment buildup, a regular filter change helps protect your refrigerator’s internal components. This can extend the lifespan of your appliance and minimize costly repairs.
Improved Health
Impurities and contaminants removed by the filter can have negative health effects. Regularly replacing the filter ensures your drinking water is free of harmful substances and supports your well-being.
Enhanced Water Flow
A clogged filter can restrict water flow, impacting the efficiency of your refrigerator. A fresh filter allows water to pass through smoothly, maintaining optimal water pressure and performance.
Reduced Appliance Noise
Sediment buildup can cause internal components to work harder and produce noise. A new filter minimizes this noise and promotes a quieter operating refrigerator.
Energy Savings
A clean filter allows your refrigerator to work more efficiently, using less energy to cool water and produce ice. Regular filter changes can contribute to reduced energy consumption and lower utility bills.
Peace of Mind
Knowing that your drinking water is clean and free of contaminants provides peace of mind. Regularly changing the filter ensures your family has access to safe and refreshing water at all times.
Additional Considerations
1. Choose the Right Filter
Ensure you select the correct filter compatible with your specific Kenmore refrigerator model. Refer to your user manual or the manufacturer’s website for guidance.
2. Turn Off Water Supply
Before starting the process, turn off the water supply to the refrigerator. Locate the water shut-off valve and close it tightly.
3. Locate the Water Filter Housing
Locate the water filter housing in your refrigerator. It is typically found on the inside of the refrigerator at the back or bottom.
4. Remove the Old Filter
Twist the old filter counterclockwise to release it from the housing. Pull it straight down to remove it completely.
5. Inspect and Clean the Housing
Once the old filter is removed, inspect the inside of the housing for any debris or contamination. Clean it with a soft cloth or sponge if necessary.
6. Prepare the New Filter
Remove the protective cap from the new filter. Soak it in cold water for a few minutes to activate it, then shake off excess water.
7. Insert the New Filter
Align the new filter with the housing and push it straight up until it clicks into place. Twist it clockwise to secure it.
8. Turn On Water Supply and Check for Leaks
Turn the water supply back on and check for any leaks around the filter housing. If there are leaks, tighten the filter or contact a qualified plumber.
9. Reset the Water Filter Indicator
Locate the water filter indicator on your refrigerator’s control panel and reset it to indicate a new filter has been installed. The exact procedure for resetting may vary depending on your specific model.
10. Flush Water Lines
After changing the filter, flush 2-3 gallons of water through the dispenser to remove any impurities or air pockets in the water lines. This ensures the water flowing through the refrigerator is clean and filtered.
Action | Estimated Time |
---|---|
Shut off water supply | 1 minute |
Locate water filter housing | 1-2 minutes |
Remove old filter | <1 minute |
Inspect and clean housing | 1-2 minutes |
Prepare new filter | <1 minute |
Insert new filter | <1 minute |
Turn on water supply | 1 minute |
Check for leaks | <1 minute |
Reset water filter indicator | <1 minute |
Flush water lines | 5-10 minutes |