Pez candy dispensers are a classic childhood treat, and they’re still enjoyed by people of all ages today. If you’ve ever wondered how to fill a Pez dispenser, you’re in luck! It’s a quick and easy process that only takes a few minutes.
To fill a Pez dispenser, you’ll need a pack of Pez candy and a dispenser. Start by removing the top of the dispenser. Then, hold the dispenser upside down and pour the candy into the opening. Tap the dispenser gently to help the candy settle. Once the dispenser is full, replace the top and you’re ready to enjoy your candy!
Here are a few tips for filling a Pez dispenser:
– Use fresh candy. Old candy can be stale and hard, and it won’t dispense properly.
– Don’t overfill the dispenser. If the dispenser is too full, the candy will get stuck and won’t come out.
– If the candy gets stuck, try tapping the dispenser gently on a hard surface. This should help to dislodge the candy and get it moving again.
Unpacking the Pez Dispenser
To begin, carefully extract the Pez dispenser from its packaging. The packaging may vary depending on the specific dispenser you have, but generally, it will be enclosed in a plastic or cardboard container. Gently remove the dispenser from the container, taking care not to damage it.
Once the dispenser is removed, inspect it for any visible defects or damage. Ensure that the dispenser is intact and has no cracks or breaks. If any damage is found, it is recommended to contact the manufacturer or retailer for assistance.
Before filling the dispenser, it is essential to remove the cap or lid. The cap is typically located at the top of the dispenser and can be removed by gently pulling it upwards. Once the cap is removed, you will have access to the dispenser’s internal chamber where the candy is stored.
Next, remove the small rubber insert that is located inside the chamber. This insert helps to keep the candy in place and prevent it from spilling out when the dispenser is opened. Gently pull the insert out and set it aside for later use.
Now that the dispenser is ready to be filled, proceed to the next step in the process.
Separating the Stem and Base
To separate the stem and base of a Pez candy dispenser, follow these steps:
1. Locate the Seam
Examine the dispenser and find the seam where the stem and base meet. It will usually be a thin, recessed line around the circumference of the dispenser.
2. Insert a Prying Tool
Take a thin, flat object, such as a butter knife or flathead screwdriver. Carefully insert the tool into the seam, applying gentle pressure to pry the stem and base apart. Note: Use caution to avoid damaging the dispenser.
| Tool | Tips |
|---|---|
| Butter Knife | Thin, rounded edge minimizes damage. |
| Plastic Knife | Plastic material reduces the risk of scratching. |
| Flathead Screwdriver | Flat tip fits into narrow seams. Use with care. |
3. Separate the Stem
Once the prying tool is inserted, gently twist and pry it to widen the seam. Continue prying until the stem and base come apart, revealing the candy chamber inside.
Additional Tips:
* If the dispenser is particularly difficult to separate, use a small amount of WD-40 or lubricant to help loosen the seam.
* Be patient and gentle when prying the dispenser apart to avoid cracking or breaking it.
* If you are having trouble separating the dispenser, you can tap it lightly on a flat surface while prying to help loosen it.
Inserting the Pez Candy
Now that you have your empty PEZ candy dispenser, it’s time to fill it with delicious candy. Here is a step-by-step guide to help you do it with ease:
-
Select the Candy
Choose the PEZ candy of your choice. PEZ offers a wide variety of flavors, so you can find one that suits your taste buds.
-
Orient the Candy
Hold the candy vertically, with the flat side facing up. The flat side should be the one with the PEZ logo or design on it.
-
Insert into the Stem
Gently insert the flat side of the candy into the stem of the PEZ dispenser. Make sure that the candy is firmly seated in the stem and is not hanging loose. If the candy is too large or small, it may not fit properly into the stem. In this case, try a different flavor or adjust the candy slightly until it fits.
Tip If you find it difficult to insert the candy, you can use a small spoon or toothpick to gently push it into the stem. -
Push the Stem
Once the candy is inserted, push the stem backward toward the back of the dispenser. You should hear a clicking sound as the stem locks into place, securing the candy inside the dispenser.
-
Dispensing the Candy
Your PEZ candy dispenser is now ready to dispense delicious candy. Simply pull the lever forward to release the candy from the stem and enjoy!
Sliding the Stem into the Base
4. Once the base is ready, it’s time to insert the stem. The stem has a small rectangular tab on one end, which fits into a corresponding slot in the base. Gently align the tab on the stem with the slot in the base.
Next, firmly push the stem into the base until it is snugly in place. Be careful not to push too hard, as you could damage the dispenser. If the stem is not all the way in, the dispenser may not work properly.
Once the stem is in place, flip the dispenser upside down and give it a shake. If the stem is properly inserted, the candy should fall out of the dispenser.
|
Candy Dispenser Parts
|
|—–|
| Part | Description |
|—–|
| Base | The bottom part of the dispenser that holds the candy. |
| Stem | The middle part of the dispenser that the candy falls through. |
| Head | The top part of the dispenser that covers the stem and candy. |
Aligning the Dispenser Head
Before you start filling, it’s crucial to align the dispenser head correctly. Here’s how:
- Remove the head: Gently twist and pull the dispenser head upward to remove it from the base.
- Examine the tabs: On the inside of the head, you’ll find two small tabs that fit into corresponding slots on the base.
- Align the tabs: Hold the head parallel to the base and carefully align the tabs with the slots.
- Push the head down: Once the tabs are aligned, gently push the head down onto the base until it clicks into place.
- Placement is key: Pay attention to the placement of the opening in the head. It should be positioned directly over the hole in the base where the candy will drop through.
Table: Troubleshooting Dispenser Head Alignment
| Issue | Possible Cause | Solution |
|---|---|---|
| Head doesn’t fit | Misaligned tabs | Realign tabs and push down |
| Candy doesn’t drop | Head not aligned properly | Remove and realign head, ensuring opening is over hole |
| Head falls off | Tabs not fully engaged | Push down firmly until it clicks into place |
Locking the Head into Place
Once the candy and stem have been inserted, it’s time to secure the head in place. This process involves carefully aligning the head with the base and applying pressure to lock it into place.
To lock the head, follow these detailed steps:
- Align the Head: Hold the head upright and position it over the base. Make sure the arrows on the head and base are aligned.
- Apply Pressure: Using your thumb or index finger, apply downward pressure on the top of the head.
- Slide the Head: While maintaining pressure, gently slide the head towards the base until it clicks into place.
- Listen for the Click: You should hear a faint click when the head is fully locked.
- Check the Lock: Gently pull on the head to ensure it is securely locked. It should not move or detach easily.
- Confirm Alignment: Once the head is locked, check that the arrows on the head and base are still aligned. If they are not, adjust the head slightly until they align correctly.
- Hold the dispenser upside down with the candy hole facing up.
- Line up the candy button with the candy hole.
- Insert the button into the hole and press down until it clicks into place.
- Make sure the candy button is aligned correctly with the candy hole. If the button is not aligned, it will not dispense candy properly.
- Press down on the candy button firmly until it clicks into place. This will ensure that the button is secure and will not fall out when you use the dispenser.
- If you have trouble inserting the candy button, try using a pair of pliers or tweezers to help you.
- Candy Blockage: Check if the candy is stuck in the dispenser tube. Use a small object, such as a toothpick, to gently dislodge any blockages.
- Insufficient Candy: Make sure there is enough candy in the base. If the base is not full, the dispenser may not dispense candy properly.
- Bent Candy Strip: The Pez candy strip should be straight and not bent. If the strip is bent, it may not feed the candy correctly.
- Loose Parts: Check if the dispenser head is securely attached to the base. If the parts are loose, the candy may not dispense smoothly.
- Store your Pez dispensers in a cool, dry place. This will help to keep the candy fresh.
- Don’t overfill your Pez dispensers. This can make it difficult to get the candy out.
- Be careful not to drop your Pez dispensers. This can damage the dispenser and make it difficult to use.
- Share your Pez candy with friends and family! Pez candy is a great way to bring people together.
- A Pez candy dispenser
- Pez candies
- A small spoon or other utensil
Troubleshooting Locking Issues
If you encounter any difficulties locking the head into place, consult the following table for potential solutions:
| Problem | Solution |
|---|---|
| Head won’t lock into place | Check if the candy and stem are inserted properly. Clean the base and head if there is any debris. |
| Head moves or detaches easily | Reapply pressure and ensure the head is fully locked. Align the arrows correctly. |
| Arrows on head and base misaligned | Unlock the head and reinsert it, aligning the arrows correctly. |
Inserting the Candy Button
Now that the dispenser is loaded with candy, it’s time to insert the candy button. The button is a small, plastic piece that fits into the top of the dispenser. It has a spring-loaded mechanism that dispenses the candy when pressed.
To insert the candy button, follow these steps:
Once the candy button is inserted, the dispenser is ready to use. To dispense candy, simply press the button down. The candy will fall out of the candy hole and into your mouth.
Tips for Inserting the Candy Button
Troubleshooting
| Problem | Solution |
|---|---|
| The candy button is not dispensing candy. | Make sure the candy button is aligned correctly with the candy hole. If the button is not aligned, it will not dispense candy properly. |
| The candy button is stuck. | Try using a pair of pliers or tweezers to help you remove the candy button. |
Aligning the Pez Stem Guide
The Pez stem guide is a small, plastic rod that helps to hold the Pez candies in place. To align the stem guide, follow these steps:
1. Hold the Pez dispenser upside down so that the candy chute is facing you.
2. Locate the small, plastic tab on the bottom of the dispenser.
3. Insert the tip of a paperclip or a small screwdriver into the tab and gently pry it open.
4. The stem guide will now be loose. You can now align it so that it is perpendicular to the candy chute.
5. Once the stem guide is aligned, press the tab back into place to secure it.
6. Your Pez dispenser is now ready to be filled with candy.
Pez Candy Dimensions
Below is a table of the dimensions of Pez candies and dispensers:
| Candy | Length | Width | Height |
|---|---|---|---|
| Regular Pez candy | 1.2 cm (0.47 in) | 0.8 cm (0.31 in) | 0.6 cm (0.24 in) |
| Large Pez candy | 1.9 cm (0.75 in) | 1.2 cm (0.47 in) | 0.9 cm (0.35 in) |
| Pez dispenser | 8.9 cm (3.5 in) | 2.5 cm (1 in) | 1.6 cm (0.63 in) |
Attaching the Pez Dispenser Base
The base of the Pez dispenser is the foundation that holds the candy and the dispenser head in place. To attach the base, follow these steps:
1. Position the Base
Align the base with the bottom of the dispenser head, ensuring that the tabs on the base fit into the slots on the head.
2. Press Down
Firmly press down on the base until it clicks into place. The tabs should lock securely into the slots.
3. Check the Connection
Pull gently on the base to verify that it is securely attached. If it moves, press down harder to ensure a tight connection.
4. Fill the Base
Unscrew the top of the base by turning it counterclockwise. Pour in the desired amount of Pez candy pellets.
5. Replace the Top
Screw the top back onto the base clockwise, ensuring that it is tightly sealed.
6. Insert the Pez Candy Strip
Take a Pez candy strip and insert it into the slot on the bottom of the dispenser head. The strip should slide easily into place.
7. Load the Candy
Push the Pez candy strip up into the dispenser head until the first candy pellet drops into the dispenser tube.
8. Dispense the Candy
Holding the dispenser upright, press down on the head to dispense a single Pez candy pellet.
9. Troubleshooting Tips
If the Pez candy dispenser is not dispensing candy properly, try the following troubleshooting tips:
How To Fill A Pez Candy Dispenser
Pez candy dispensers are a classic candy treat that have been enjoyed by people of all ages for generations. They come in a variety of shapes and sizes, and can be filled with a variety of different candies. If you’re new to Pez dispensers, or if you just need a refresher on how to fill them, here are some simple instructions.
1. Remove the head of the dispenser.
To do this, simply pull the head straight up. The head should come off easily.
2. Fill the dispenser with candy.
You can use any type of candy that you like, but Pez candies are the most popular choice. To fill the dispenser, simply pour the candy into the hole in the back of the head.
3. Replace the head of the dispenser.
Once the dispenser is filled, simply push the head back on. The head should fit snugly into place.
4. Enjoy your Pez candy!
Now that your Pez dispenser is filled, you can enjoy your delicious candy treat. Simply press down on the head of the dispenser to release a single candy.
Enjoying Your Pez Candy
Pez candy dispensers are a great way to enjoy your favorite candy. They’re portable, so you can take them with you wherever you go. They’re also a fun and easy way to share candy with friends and family.
Here are a few tips for enjoying your Pez candy:
Pez Candy Dispensers Through the Years
Pez candy dispensers have been around for over 90 years. They were first introduced in Austria in 1927, and they quickly became popular all over the world. Pez dispensers have been made in a variety of shapes and sizes over the years, and they have featured a wide variety of characters, including cartoon characters, movie stars, and sports figures.
Today, Pez candy dispensers are still a popular candy treat. They are a fun and easy way to enjoy your favorite candy, and they are a great way to share candy with friends and family.
Pez Candy Dispenser Value
Pez candy dispensers can be a valuable collector’s item. Some rare Pez dispensers can sell for hundreds or even thousands of dollars. The value of a Pez dispenser depends on a number of factors, including its age, rarity, and condition.
Pez Candy Dispenser Collecting
Pez candy dispenser collecting is a popular hobby. There are many different Pez dispensers to collect, and there is a large community of collectors who share their knowledge and passion for Pez candy dispensers.
If you are interested in starting a Pez candy dispenser collection, there are a few things you should keep in mind:
| Factor | Description |
|---|---|
| Age | Older Pez dispensers are generally more valuable than newer ones. |
| Rarity | Pez dispensers that were produced in limited quantities are more valuable than those that were produced in large quantities. |
| Condition | Pez dispensers that are in good condition are more valuable than those that are damaged or worn. |
How To Fill A Pez Candy Dispenser
To fill a Pez candy dispenser, you will need the following:
First, remove the head of the Pez dispenser by pulling it straight up. Next, use the spoon or other utensil to fill the dispenser with Pez candies. Be careful not to overfill the dispenser, as this can make it difficult to insert the head back on.
Once the dispenser is filled, insert the head back on by aligning the two tabs on the head with the slots on the dispenser. Press down on the head until it snaps into place.
People Also Ask About How To Fill A Pez Candy Dispenser
How do you open a Pez dispenser?
To open a Pez dispenser, pull the head straight up.
How do you put the head back on a Pez dispenser?
To put the head back on a Pez dispenser, align the two tabs on the head with the slots on the dispenser and press down until it snaps into place.
How many Pez candies fit in a dispenser?
A Pez candy dispenser can hold approximately 12 Pez candies.
