1. How to Program Your RC73 DIRECTV Remote

DIRECTV RC73 remote

Have you recently purchased a Directv receiver and are looking for a hassle-free way to program your Rc73 remote? Look no further, as this comprehensive guide will provide you with step-by-step instructions to effortlessly pair your remote with your receiver and enjoy a seamless television experience. Whether you’re a seasoned Directv user or new to the platform, this article will empower you with the necessary knowledge to program your Rc73 remote swiftly and effectively.

To initiate the programming process, gather your Rc73 remote and Directv receiver within close proximity. Ensure that both devices are powered on and within line of sight of each other. Subsequently, locate the “Menu” button on your remote and press it repeatedly until the “Remote Control” menu appears on your television screen. Utilize the arrow keys to navigate the menu and select the “Program Remote” option. This action will prompt the remote to enter programming mode, indicated by a blinking red light located at its top.

Next, you will need to locate the specific code corresponding to your Directv receiver model. Consult the user manual or Directv’s official website to obtain the correct code. Once you have the code, enter it using the number keys on your remote. As you input each digit, the red light on the remote will flash. After entering the complete code, press the “Enter” button to finalize the programming process. The remote will then automatically pair with your receiver, and you will be able to control your Directv system effortlessly. Should you encounter any difficulties during the programming process, do not hesitate to consult the troubleshooting tips provided in the subsequent sections of this guide.

Pairing the RC73 Remote with Your DIRECTV Receiver

Step 1: Verify Compatibility

Before proceeding, ensure that your RC73 remote is compatible with your DIRECTV receiver. Refer to the user manual or DIRECTV website for a list of compatible models.

Step 2: Clear Existing Codes

If the remote was previously paired with another device, you must clear the existing codes. To do this, simultaneously press and hold the “SAT” and “SELECT” buttons for approximately 10 seconds, until the LED light on the remote blinks twice.

Step 3: Enter Pairing Mode

Bring the RC73 remote within 12 inches of your DIRECTV receiver. Press and hold the “DIRECTV” button for 3 seconds, until the LED light blinks twice.

Step 4: Enter Pairing Code

Refer to the table below for the appropriate pairing code for your DIRECTV receiver model. Using the number pad on the remote, enter the corresponding three-digit code.

Receiver Model	Pairing Code
HR20-100	101
HR21-100	102
HR22-100	103
HR23-100	104
HR24-100	105

Step 5: Verification

After entering the pairing code, the LED light on the remote should blink twice, indicating successful pairing. Test the remote by pressing the “POWER” button to turn on your DIRECTV receiver.

Controlling Your TV with the RC73 Remote

The RC73 remote is a universal remote that can be programmed to control a variety of TVs from different manufacturers. Programming the remote is a simple process that can be done in a few minutes.

Pairing the RC73 Remote with Your TV

Turn on your TV.
Press and hold the “TV” button on the RC73 remote until the green LED light flashes twice.
Enter the five-digit code for your TV manufacturer from the table below.
Press the “OK” button on the remote.
The green LED light will flash three times to indicate that the remote has been paired with your TV.

TV Manufacturer	Code
Samsung	10001
LG	10002
Sony	10003
Vizio	10004
TCL	10005

Using the RC73 Remote to Control Your TV

Once the RC73 remote is paired with your TV, you can use it to control all of the basic functions of your TV, including:

Powering on and off
Changing channels
Adjusting the volume
Muting the sound
Accessing the TV’s menu

Troubleshooting Common Problems with the RC73 Remote

If you are having problems using the RC73 remote to control your TV, there are a few things you can try:

Make sure that the batteries in the remote are fresh.
Make sure that the remote is pointed directly at the TV.
Check to see if there are any obstructions between the remote and the TV.
Try resetting the remote by pressing and holding the “TV” button and the “OK” button for five seconds.

Troubleshooting Common RC73 Remote Issues

1. Check Batteries

Ensure that the batteries are fresh and properly inserted. Replace them if necessary.

2. Verify Line of Sight

Ensure that the remote has a clear line of sight to the TV. Remove any obstructions between the two.

3. Reset the Remote

Hold down the “Reset” button on the back of the remote for 5 seconds. This will restore the device to its factory settings.

4. Re-Pair the Remote

Follow the instructions on the DirecTV website or refer to your user manual to re-pair the remote with your receiver to establish a new connection.

5. Advanced Troubleshooting

If the previous steps fail, try the following:

Issue	Solution
Buttons not responding	Clean the buttons with a cotton swab dipped in isopropyl alcohol. Check for any damaged or broken contacts.
Remote controls other devices	Program the remote to ignore other devices by following the steps in the user manual.
Intermittent connectivity	Check the cords and connections between the receiver and the TV. Ensure they are secure and not damaged.

Using the RC73 Remote to Access Advanced Settings

Advanced Settings Accessible through the RC73 Remote

The RC73 remote provides access to a wide range of advanced settings, allowing users to customize their DIRECTV experience to their liking. Some of these settings include:

Parental Controls
Device Setup
Audio Options
Display Settings
Network Settings
System Information

Accessing Advanced Settings

To access the advanced settings menu, follow these steps:

Press the “Menu” button on the RC73 remote.
Use the arrow keys to navigate to the “Settings” option and press “Select.”
Scroll down to the “Advanced Settings” option and press “Select.”

Navigating the Advanced Settings Menu

The advanced settings menu is organized into submenus, each covering a specific aspect of the settings. Use the arrow keys to navigate between submenus and press “Select” to enter a submenu.

Saving Changes

After making changes to the advanced settings, remember to save them. To do so, press the “Save” button at the bottom of the settings menu.

Troubleshooting

If you encounter any issues accessing or using the advanced settings, refer to the DIRECTV support website or contact customer service for assistance.

Error	Solution
Unable to access the advanced settings menu	Check if the remote batteries are fresh and properly installed.
Changes made to the advanced settings are not saved	Ensure that you press the “Save” button before exiting the settings menu.

Replacing the RC73 Remote’s Batteries

To replace the batteries in your RC73 remote, follow these steps:

Slide the battery compartment cover down and remove it.
Remove the old batteries.
Insert two new AA batteries into the compartment, making sure to match the positive and negative terminals.
Slide the battery compartment cover back into place.

Inserting Batteries with Correct Polarity

It is crucial to insert the batteries with the correct polarity. Improper battery insertion can damage the remote or cause it to malfunction. To ensure correct polarity, align the positive terminal (+) of the battery with the positive terminal inside the battery compartment, and the negative terminal (-) with the negative terminal.

Correct Polarity	Incorrect Polarity

If you are unsure about the correct polarity, refer to the diagram or markings inside the battery compartment.

Maximizing the Functionality of the RC73 Remote

1. Pairing with Your DIRECTV Box

Ensure the DIRECTV box and remote are within line of sight. Press the “SAT” button to turn on the receiver. Hold the “DASH” button and the “SELECT” button simultaneously for 3 seconds. Release both buttons when the receiver’s LED flashes twice. Point the remote at the receiver and press the “ENTER” button to complete the pairing process.

2. Programming a TV

Press the TV power button on the RC73. Hold the “SELECT” and “TV” buttons for 3 seconds. Enter the 3-digit or 5-digit code for your TV brand. Press the “ENTER” button. To confirm the programming, press the TV power button again and it should turn on or off.

3. Adjusting Audio Settings

Adjust the volume using the volume controls. Press the “MUTE” button to silence the audio. To control other audio settings, such as the equalizer or surround sound, use the “AUDIO” button.

4. Navigating Menus

Use the directional pad to navigate through the DIRECTV menus. The “SELECT” button confirms selections, while the “BACK” button returns to the previous menu. To exit the menus, press the “EXIT” button.

5. Switching Inputs

Press the “INPUT” button to cycle through the available inputs on your TV. You can also use the “SELECT” button to choose a specific input.

6. Changing Channels

Enter the channel number directly into the number pad. Use the channel up/down buttons to browse channels. Press the “LAST” button to return to the previous channel.

7. Accessing Favorite Channels

Press the “FAV” button to display a list of your favorite channels. Use the directional pad to select a channel and press “SELECT” to watch it.

8. Using Advanced Features

Hold the “SAT” button and press the number keys to access advanced features, such as parental controls, settings, and diagnostics.

9. Customizing Buttons

Hold the “SAT” button and press the “My Button” button. Choose a button to customize and then press a command key to assign a specific function.

10. Troubleshooting

If you encounter any issues with the RC73 remote, refer to the following troubleshooting table:

Issue	Solution
Remote is not responding	Check battery levels and replace if necessary.
Cannot pair with DIRECTV box	Reset the remote by removing the batteries and pressing the “CLEAR” button on the bottom of the remote.
No picture or sound	Ensure that the TV and receiver are connected properly and that the input is correct.
Cannot access advanced features	Hold the “SAT” button for a longer period to enter advanced mode.
Custom buttons not working	Reset the customized buttons by holding the “SAT” button and pressing the “CLEAR” button.

How to Program RC73 DIRECTV Remote

The RC73 is a universal remote control that can be programmed to operate multiple devices, including DIRECTV receivers. If you have lost the original remote for your DIRECTV receiver or simply want to use a single remote for all of your devices, you can follow these steps to program the RC73 remote to work with your DIRECTV receiver.

You will need the following items:

RC73 remote control
DIRECTV receiver
Phillips head screwdriver (optional)

Step 1: Open the battery compartment of the RC73 remote control.

There is a small screw on the back of the remote that needs to be removed. Once the screw is removed, the battery compartment will open.

Step 2: Insert the batteries into the battery compartment.

The RC73 remote control uses two AA batteries. Make sure that the batteries are inserted correctly, with the positive (+) terminal facing up.

Step 3: Close the battery compartment.

Once the batteries are inserted, close the battery compartment and tighten the screw.

Step 4: Point the RC73 remote control at the DIRECTV receiver.

Make sure that the remote is within a few feet of the receiver and that there are no obstructions between the remote and the receiver.

Step 5: Press and hold the “SAT” button on the RC73 remote control.

The SAT button is located on the top of the remote, next to the power button. Hold the button down for about 5 seconds, until the red light on the remote starts to blink.

Step 6: Enter the 5-digit code for your DIRECTV receiver.

The 5-digit code for your DIRECTV receiver can be found on the bottom of the receiver. If you cannot find the code on the receiver, you can look it up online or call DIRECTV customer service.

Step 7: Press the “#” button on the RC73 remote control.

The red light on the remote will stop blinking and the remote will be programmed to work with your DIRECTV receiver.