Keurig coffee makers are a popular way to make a quick and easy cup of coffee. However, if your Keurig starts to malfunction, you may need to take it apart to troubleshoot the problem. Taking apart a Keurig can seem like a daunting task, but it is actually quite simple with the right tools and instructions.
Before you start taking apart your Keurig, be sure to unplug it from the power outlet. You will also need to gather a few tools, including a Phillips head screwdriver, a flathead screwdriver, and a pair of pliers. Once you have your tools, you can follow the steps below to take apart your Keurig:
First, remove the water reservoir. The water reservoir is located on the back of the Keurig. To remove it, simply lift it up and pull it out. Next, remove the drip tray. The drip tray is located under the brew head. To remove it, simply pull it out. Finally, remove the brew head. The brew head is located at the top of the Keurig. To remove it, turn the locking lever to the unlock position and pull the brew head up and out.
Disassembling the Outer Casing
Before you can access the inner workings of your Keurig, you need to disassemble the outer casing. This is a relatively simple process, but it’s important to follow the steps carefully to avoid damaging your coffee maker.
1. Remove the top cover
Start by removing the top cover of the Keurig. On most models, the top cover is held in place by two screws located at the back of the machine. Use a Phillips head screwdriver to remove the screws, then lift the top cover off the machine.
Once the top cover is removed, you will see the water reservoir and the brewing chamber. The water reservoir is located on the left side of the machine, and the brewing chamber is located on the right side.
To remove the water reservoir, simply lift it up and out of the machine. To remove the brewing chamber, press down on the release button located on the top of the chamber, then lift the chamber out of the machine.
2. Remove the side panels
The next step is to remove the side panels of the Keurig. On most models, the side panels are held in place by two screws located at the top and bottom of each panel. Use a Phillips head screwdriver to remove the screws, then lift the side panels off the machine.
Once the side panels are removed, you will see the internal components of the Keurig. These components include the heating element, the pump, and the control board.
3. Remove the bottom cover
The final step is to remove the bottom cover of the Keurig. On most models, the bottom cover is held in place by four screws located at the corners of the cover. Use a Phillips head screwdriver to remove the screws, then lift the bottom cover off the machine.
Once the bottom cover is removed, you will have access to all of the internal components of the Keurig. You can now begin troubleshooting or repairing your coffee maker.
Removing the Water Reservoir
Removing the water reservoir is simple and can be done in just a few steps. Make sure that the coffee maker is turned off and unplugged before starting.
1. Locate the water reservoir release button.
The water reservoir release button is usually located on the back or side of the coffee maker. It is typically a small, black button.
2. Press the water reservoir release button and pull the reservoir straight up.
Once you have located the water reservoir release button, press it and pull the reservoir straight up. The reservoir should come out easily. If you are having trouble removing the reservoir, try wiggling it gently from side to side.
The reservoir has a variety of internal components that may dislodge during the removal or filling process. Here’s a visual guide to help identify these components:
| Component | Description |
|---|---|
| Water Level Indicator | A float that rises and falls with the water level. |
| Water Level Sensor | A sensor that detects the water level and shuts off the coffee maker when the reservoir is empty. |
| Pump | A pump that circulates the water through the coffee maker. |
3. Once the reservoir has been removed, you can clean it with warm, soapy water.
Make sure to rinse the reservoir thoroughly and allow it to dry completely before replacing it.
Disconnecting the Electrical Wires
Once you’ve removed the outer casing, it’s time to disconnect the electrical wires. These wires are what power the Keurig, so it’s important to be careful when handling them.
Step 1: Locate the Electrical Wires
The electrical wires are located on the bottom of the Keurig. They’re usually held in place by a plastic clip.
Step 2: Remove the Plastic Clip
Use a screwdriver or your fingernails to remove the plastic clip. This will release the electrical wires.
Step 3: Disconnect the Electrical Wires
Once the electrical wires are released, you can disconnect them. To do this, simply pull the wires apart.
| Wire Color | Connection |
|---|---|
| Black | Common |
| Red | Line |
| White | Neutral |
Removing the Plunger and Needles
To remove the plunger and needles, first remove the top cover of the Keurig. Then, locate the plunger assembly. It is a cylindrical-shaped part that is located in the center of the machine. Grip the plunger assembly and pull it straight up. This will remove the plunger and needles from the machine.
Once the plunger and needles have been removed, you can clean them. To clean the plunger, simply wipe it down with a damp cloth. To clean the needles, use a soft brush to remove any coffee grounds or debris. Once the plunger and needles are clean, you can reassemble the Keurig.
Cleaning the Plunger Assembly
| Step | Description |
|---|---|
| 1 | Remove the top cover of the Keurig. |
| 2 | Locate the plunger assembly. It is a cylindrical-shaped part that is located in the center of the machine. |
| 3 | Grip the plunger assembly and pull it straight up. This will remove the plunger and needles from the machine. |
| 4 | Wipe down the plunger with a damp cloth. |
| 5 | Use a soft brush to remove any coffee grounds or debris from the needles. |
| 6 | Reassemble the Keurig. |
Accessing the Internal Components
To access the internal components of the Keurig machine, you must carefully disassemble the exterior housing. Here’s a step-by-step guide to do so:
1. Unplug the Machine
Begin by unplugging the Keurig machine from the power outlet to ensure your safety.
2. Locate the Screws
Next, locate the screws that hold the exterior housing together. On most Keurig models, these screws are found on the back of the machine or underneath the drip tray.
3. Remove the Exterior Housing
Use a screwdriver to remove the screws, and then gently lift the exterior housing off the machine. Be careful not to damage any wires or internal components.
4. Locate the Screws Holding the Chassis
Inside the exterior housing, you will find the chassis, which holds the internal components in place. Locate the screws that hold the chassis in place, which are typically found on the sides or bottom.
5. Remove the Chassis
Use a screwdriver to remove the screws, and then carefully lift the chassis out of the machine. Take care not to pull any wires or damage any components.
6. Troubleshooting
Sometimes during disassembly, you may encounter some common issues. Here’s a troubleshooting guide to help you resolve them:
| Issue | Solution |
|---|---|
| Stripped screw | Use a rubber band or small piece of paper between the screwdriver and the screw to gain extra grip. |
| Stuck components | Gently tap on the component with a rubber mallet or use a thin, flat tool to pry it apart. |
| Damaged or disconnected wires | Inspect the wires for any damage or disconnection. If necessary, reconnect or repair the wires using wire connectors or electrical tape. |
Disconnecting the Control Board
Once you’ve removed the top cover and front panel, it’s time to disconnect the control board. This is a delicate step, so take your time and be careful not to damage any of the components.
Step 1: Identify the Control Board
The control board is usually located in the center of the machine, behind the front panel. It’s a green circuit board with a number of wires and connectors attached to it.
Step 2: Disconnect the Wires
Use a pair of needle-nose pliers to disconnect the wires from the control board. There are two types of wires: power wires and data wires. Power wires are usually thicker and have a black or red insulation. Data wires are thinner and have a yellow or white insulation.
Step 3: Remove the Connectors
Once the wires are disconnected, you can remove the connectors from the control board. Connectors are small plastic plugs that connect the wires to the board. To remove a connector, gently pry it up with a small screwdriver.
Step 4: Lift the Control Board
Once the connectors are removed, you can lift the control board up and out of the machine. Be careful not to damage any of the components on the board.
Step 5: Place the Control Board in a Safe Location
Once the control board is removed, place it in a safe location where it won’t get damaged. You can put it in a plastic bag or wrap it in a towel.
Step 6: Double-Check Your Work
Before you move on to the next step, double-check your work to make sure that all of the wires and connectors are disconnected from the control board. This will help to prevent any damage to the machine when you reassemble it.
Step 7: Troubleshooting Tips
If you’re having trouble disconnecting the control board, here are a few troubleshooting tips:
| Problem | Solution |
|---|---|
| I can’t disconnect the wires from the control board. | Make sure that you’re using the correct type of pliers. Needle-nose pliers are the best type of pliers for this job. |
| I can’t remove the connectors from the control board. | Try using a small screwdriver to gently pry the connectors up. Be careful not to damage the connectors or the board. |
| I accidentally damaged the control board. | If you accidentally damaged the control board, you will need to replace it. You can purchase a replacement control board from the manufacturer of your Keurig machine. |
Removing the Flow Sensor
The flow sensor is a small, plastic component located in the water line of your Keurig. It helps to determine how much water is pumped into the brew chamber. To remove the flow sensor, follow these steps:
1. Unplug the Keurig
Before you begin, make sure that the Keurig is unplugged from the electrical outlet.
2. Locate the flow sensor
The flow sensor is located on the bottom of the Keurig, near the water line.
3. Remove the screws
There are two screws that hold the flow sensor in place. Remove these screws using a Phillips head screwdriver.
4. Disconnect the wires
Once the screws are removed, you will need to disconnect the two wires that are connected to the flow sensor.
5. Remove the flow sensor
Once the wires are disconnected, you can remove the flow sensor by gently pulling it out of the water line.
6. Inspect the flow sensor
Once you have removed the flow sensor, take a moment to inspect it for any damage. If the flow sensor is damaged, it will need to be replaced.
7. Clean the flow sensor
If the flow sensor is not damaged, you can clean it by rinsing it with water.
8. Reinstall the flow sensor
To reinstall the flow sensor, simply reverse the steps that you took to remove it. Be sure to tighten the screws securely, but do not overtighten them.
Disassembling the Drip Tray
1. **Locate the drip tray latch:** The drip tray is held in place by a latch located on the bottom of the machine.
2. **Press the latch:** Firmly press down on the latch to release it.
3. **Pull out the drip tray:** Once the latch is released, gently pull out the drip tray.
4. **Remove the cup support:** The cup support is a small plastic piece that sits inside the drip tray. Grasp the cup support and pull it straight up to remove it.
5. **Clean the drip tray and cup support:** Use a damp cloth to wipe down the drip tray and cup support. If there is any coffee residue, use a mild detergent to clean it off.
6. **Reassemble the drip tray:** Place the cup support back into the drip tray, then insert the drip tray back into the machine.
7. **Close the latch:** Push down on the latch to secure the drip tray in place.
Removing the Drip Tray Float
8. **Locate the drip tray float:** The drip tray float is a small plastic ball that sits inside the drip tray. It helps to detect when the drip tray is full.
9. **Remove the drip tray float:** To remove the drip tray float, gently push down on the float and pull it out of the drip tray. The float is held in place by a small magnet, so it may require a little force to remove it.
| Step | Action |
|---|---|
| 1 | Locate the drip tray latch. |
| 2 | Press the latch. |
| 3 | Pull out the drip tray. |
| 4 | Remove the cup support. |
| 5 | Clean the drip tray and cup support. |
| 6 | Reassemble the drip tray. |
| 7 | Close the latch. |
| 8 | Locate the drip tray float. |
| 9 | Remove the drip tray float. |
Cleaning and Reassembling the Components
Now that the Keurig is disassembled, it’s time to clean the components. Use warm, soapy water and a soft cloth to wipe down all of the removable parts. Take special care to clean the needle and the water reservoir.
Once the components are clean, it’s time to reassemble the Keurig. Start by inserting the water reservoir into the base of the machine. Then, replace the drip tray and the K-Cup holder.
Next, insert the needle into the top of the machine. Make sure that the needle is properly aligned so that it can puncture the K-Cups.
Finally, replace the top of the machine and plug in the Keurig. Your Keurig is now ready to use!
Cleaning the Water Reservoir
The water reservoir is one of the most important components of your Keurig. It’s important to clean the water reservoir regularly to prevent the buildup of mold and bacteria.
To clean the water reservoir, remove it from the Keurig and rinse it with warm water. Then, add a few drops of dish soap to the water reservoir and swish it around. Finally, rinse the water reservoir thoroughly with warm water and replace it in the Keurig.
Cleaning the Needle
The needle is another important component of your Keurig. It’s important to clean the needle regularly to prevent it from clogging. Some keurig models have a removable needle, while others do not. To clean the needle, simply use a soft cloth and gently wipe away any coffee grounds or other debris. If your Keurig model has a removable needle, you can remove it and soak it in warm, soapy water for a few minutes. Then, rinse the needle thoroughly with warm water and replace it in the Keurig.
Cleaning the K-Cup Holder
The K-Cup holder is another component of your Keurig that should be cleaned regularly. To clean the K-Cup holder, simply remove it from the Keurig and rinse it with warm water. Then, use a soft cloth to wipe away any coffee grounds or other debris. Finally, replace the K-Cup holder in the Keurig.
| Type | Cleaning method |
|---|---|
| Water reservoir | Rinse with warm water, add a few drops of dish soap, swish around, rinse thoroughly |
| Needle | Wipe with a soft cloth, remove and soak in warm, soapy water (if removable) |
| K-Cup holder | Rinse with warm water, wipe with a soft cloth |
How To Take Apart A Keurig
Here are the steps on how to take apart a Keurig:
- Unplug the Keurig and let it cool down.
- Remove the water reservoir and drip tray.
- Turn the Keurig upside down and remove the four screws that hold the bottom panel in place.
- Carefully lift the bottom panel off of the Keurig.
- Locate the two screws that hold the heating element in place and remove them.
- Carefully lift the heating element out of the Keurig.
- Locate the two screws that hold the pump in place and remove them.
- Carefully lift the pump out of the Keurig.
- Locate the two screws that hold the control board in place and remove them.
- Carefully lift the control board out of the Keurig.
People Also Ask About How To Take Apart A Keurig
How do I clean the inside of my Keurig?
To clean the inside of your Keurig, you will need to descale it. Descaling is the process of removing mineral buildup from the inside of the Keurig. You can descale your Keurig using a descaling solution or vinegar.
How do I fix a Keurig that is not brewing?
If your Keurig is not brewing, there are a few things you can check:
- Make sure that the Keurig is plugged in and turned on.
- Make sure that there is water in the water reservoir.
- Make sure that the K-cup is properly inserted into the Keurig.
- Make sure that the needle in the Keurig is not clogged.
How do I replace the water filter in my Keurig?
To replace the water filter in your Keurig, you will need to:
- Remove the water reservoir from the Keurig.
- Locate the water filter in the bottom of the water reservoir.
- Remove the old water filter and insert the new water filter.
- Replace the water reservoir in the Keurig.
