If you’re looking for a hassle-free way to trim your lawn, an Ego Power+ trimmer is a great option. These trimmers are lightweight, easy to maneuver, and produce a clean, even cut. Plus, they’re battery-powered, so you don’t have to worry about cords or gas.
Loading line into an Ego Power+ trimmer is quick and easy. First, remove the bump knob from the trimmer head. Then, insert the line into the hole in the center of the trimmer head. Be sure to leave about 6 inches of line hanging out of the hole. Next, replace the bump knob and tighten it securely. Finally, tap the trimmer head on the ground to advance the line.
Now that you know how to load line into an Ego Power+ trimmer, you’re ready to start trimming your lawn. Just remember to wear safety glasses and gloves, and to follow the manufacturer’s instructions for safe operation.
Preparing the Ego Trimmer
Before you delve into trimming, it’s crucial to prepare your Ego trimmer meticulously to ensure optimal performance and longevity. Here’s a comprehensive guide to the preparatory steps:
1. Gather Necessary Gear
Prior to initiating the trimming process, assemble the requisite equipment including:
- Ego trimmer with appropriate line
- Safety glasses
- Ear protection
- Work gloves
- Trimmer line
- Line winder (if required)
- Instruction manual
| Item | Purpose |
|---|---|
| Safety glasses | Protect your eyes from flying debris and UV rays |
| Ear protection | Shield your hearing from the noise of the trimmer |
| Work gloves | Prevent cuts and abrasions |
| Trimmer line | The cutting element of the trimmer |
| Line winder (if required) | Used to load or replace trimmer line |
Donning the appropriate safety gear not only protects you but also enhances your comfort during trimming.
Inserting the String into the Trimmer Head
Step 1: Remove the Trimmer Head Cover
Locate the latch or release mechanism on the trimmer head cover and press it to remove the cover. This will expose the trimmer head and string spool.
Step 2: Unwind the String and Feed it through the Holes
Method 1: Single-Hole Loading
* Unwind approximately 3 feet of string from the spool.
* Insert one end of the string into one of the holes on the trimmer head.
* Pull the string down through the hole and out the bottom of the trimmer head.
Method 2: Two-Hole Loading
* Unwind approximately 6 feet of string from the spool.
* Divide the string into two equal strands.
* Insert one strand into each of the holes on the trimmer head.
* Pull both strands down through the holes and out the bottom of the trimmer head.
Step 3: Thread the String through the Eyelets
Single-Hole Loading
* Thread the string through the eyelet on the top of the trimmer head.
Two-Hole Loading
* Thread one strand of string through each of the eyelets on the trimmer head.
Step 4: Cut Strings to Desired Length
* Trim the excess string to the desired length, typically around 8-10 inches.
* Ensure that the strings are not too long or too short, as this can affect the trimmer’s performance.
Step 5: Replace the Trimmer Head Cover
* Align the trimmer head cover with the base and press down firmly until it locks into place.
Winding the String onto the Spool
To wind the string onto the spool, follow these steps:
1. Remove the Spool Cover
Locate the spool cover on the trimmer head and use a screwdriver or coin to remove it.
2. Insert the String into the Spool
Take one end of the string and insert it into the small hole on the side of the spool. Pull enough string through to create a loop.
3. Wrap the String Around the Spool
Start winding the string around the spool in a clockwise direction, keeping it taut. Ensure that the string is evenly distributed across the spool to prevent tangling.
| Direction | Details |
|---|---|
| Clockwise | Wrap the string around the spool in this direction. |
| Taut | Keep the string tight as you wind it to prevent slippage. |
| Even Distribution | Spread the string evenly across the spool to avoid tangles. |
Continue winding until the spool is full or the string is almost out. Leave about 6 inches of string free at the end.
Adjusting the String Length
Follow these steps to adjust the string length on your EGO trimmer.
- Unplug the trimmer from the power source.
- Turn the trimmer upside down.
- Locate the string adjustment knob. It is typically located near the bottom of the trimmer head.
- Adjust the string length to the desired length. The recommended string length is between 4 and 6 inches. To adjust the string length, turn the knob clockwise to shorten the string or counterclockwise to lengthen it.
- Wrap the excess string around the trimmer head. This will help prevent the string from tangling.
- Plug the trimmer back into the power source.
Optimal String Length
The optimal string length for your EGO trimmer depends on the following factors:
| Factor | Recommended String Length |
|---|---|
| Type of grass |
|
| Trimming conditions |
|
| Trimming technique |
|
By adjusting the string length to the optimal setting, you can improve the performance and efficiency of your EGO trimmer.
Securing the String
1. Unwind the String
Begin by unwinding approximately 6 feet of the new trimmer string from the spool. Avoid unwinding any more string than necessary, as excess string can become tangled.
2. Insert the String
Locate the string guide on the trimmer head and insert one end of the string through the guide. Ensure that the string is fed in the direction indicated by the arrows on the guide.
3. Wind the String
Start winding the string around the trimmer spool. Wind it tightly, but avoid applying excessive force that could damage the string.
4. Thread the String
Once you have wound several loops around the spool, thread the other end of the string through the small hole located on the edge of the trimmer head.
5. Tighten the String
Firmly pull on the string that is threaded through the hole. Simultaneously, use the other hand to hold the trimmer head to prevent it from rotating. Continue pulling until the string is taut and securely wound around the spool. The string should now extend a few inches beyond the trimmer head.
6. Cut the String
Use a pair of scissors to cut the excess string, leaving approximately 2 inches of string extending beyond the trimmer head.
Here is a table summarizing the steps for securing the string:
| Step | Description |
|---|---|
| 1 | Unwind approximately 6 feet of string. |
| 2 | Insert one end of the string through the string guide. |
| 3 | Wind the string around the trimmer spool. |
| 4 | Thread the other end of the string through the hole on the trimmer head. |
| 5 | Pull on the string to tighten and hold the trimmer head. |
| 6 | Cut the excess string. |
Installing the Trimmer Head
To install the trimmer head on your Ego trimmer, follow these steps:
- Ensure that the trimmer is turned off and unplugged.
- Locate the trimmer head cap and turn it counterclockwise to remove it.
- Remove the old trimmer head by pulling it straight off the shaft.
- Clean the shaft of any debris.
- Align the new trimmer head with the shaft and slide it on until it clicks into place.
- Tighten the trimmer head cap by turning it clockwise.
Tightening the Trimmer Head Cap
To ensure that the trimmer head is securely fastened, it is important to properly tighten the trimmer head cap.
Here are the recommended torque specifications for the trimmer head cap:
| Trimmer Model | Torque Specification |
|---|---|
| ST1500 | 15-20 ft-lbs |
| ST1521 | 15-20 ft-lbs |
| BC2000 | 20-25 ft-lbs |
| BC2021 | 20-25 ft-lbs |
To achieve the proper tightness, use a torque wrench to apply the specified torque to the trimmer head cap.
Note: Overtightening the trimmer head cap can damage the cap or the shaft. Undertightening the cap can result in the trimmer head becoming loose during operation.
Loading the Battery
Inserting the Battery into the Trimmer
Locate the battery compartment on the back of the Ego Trimmer. Press the release button and pull the battery out of the compartment.
Charging the Battery
Connect the battery charger to a power outlet. Slide the battery into the charger until it snaps into place.
LED Indicators
The charger’s LED indicators will display the following statuses:
- Solid Green: Battery is fully charged.
- Flashing Green: Battery is charging.
- Solid Red: Battery is not connected properly or is faulty.
Charging Time
The charging time varies depending on the battery capacity and its remaining charge level. Refer to the table below for approximate charging times:
| Battery Capacity (Ah) | Charging Time |
|---|---|
| 2.5 | 60 minutes |
| 5 | 120 minutes |
Removing the Battery from the Charger
Once the battery is fully charged, disconnect the charger from the power outlet. Press the battery release button on the charger and pull the battery out.
Connecting the Power Supply
Before operating your Ego trimmer, it is crucial to establish a reliable connection to a power source. Follow these steps to ensure a safe and efficient connection:
- Locate the Power Outlet: Identify a suitable outdoor power outlet that is easily accessible and protected from the elements.
- Inspect the Power Cord: Examine the power cord thoroughly for any visible damage or exposed wires. Never use a damaged cord.
- Connect the Power Cord: Insert the plug end of the power cord securely into the power outlet.
- Check the Connection: Ensure the connection is snug and secure. Avoid loose or wobbly connections.
- Turn on the Power Source: Activate the power at the outlet by flipping the switch or pressing the button.
- Confirm Power Supply: Verify that the trimmer’s motor starts and runs smoothly upon connecting the power.
- Disconnect After Use: When finished using the trimmer, always disconnect the power cord from the outlet. This practice will prevent accidental starts and conserve energy.
- Proper Storage: Store the power cord neatly and securely to prevent damage and prolong its lifespan.
| Item | Description |
|---|---|
| Power Outlet | Outdoor power outlet with weather protection |
| Power Cord | Electrical cord connecting the trimmer to the power outlet |
| Power Switch | Control that activates and deactivates power at the outlet |
Verifying the String Length
When loading the string, it is essential to ensure that the line is the correct length. This will ensure that the trimmer is operating efficiently. If the string is too long, it can cause the trimmer to overheat and prematurely wear out the motor. If the string is too short, it will not be effective in cutting the grass, and it could become entangled in the trimmer head. Refer to the user manual for your specific Ego trimmer model to determine the correct string length.
A practical method for verifying the string length is the “9-inch rule.” This approach involves measuring the distance from the center of the trimmer head to the cutting tip of the string. For optimal performance, aim for a string length of approximately 9 inches on each side. This measurement ensures ample reach for effective cutting while minimizing the risk of tangling or overheating.
| Recommended String Length |
|---|
| 9 inches on each side from the center of the trimmer head |
By following the “9-inch rule,” you can ensure that your Ego trimmer is operating at its best and delivering efficient and precise cutting results.
How to Load Ego Trimmer String
Loading Ego trimmer string is a simple process that can be completed in a few easy steps.
- Unplug the trimmer from the power source.
- Locate the trimmer head. It is usually located at the end of the shaft.
- Push the release button on the trimmer head. This will open the head and allow you to access the spool.
- Remove the old string from the spool. If there is still string on the spool, you can cut it off with a pair of scissors.
- Insert the new string into the spool. The string should be wound around the spool in the direction indicated by the arrows on the spool.
- Pull the string through the hole in the trimmer head.
- Close the trimmer head. Make sure that the release button is engaged.
- Plug the trimmer back into the power source.
- Test the trimmer to make sure that the string is loaded correctly.
Troubleshooting Common Loading Issues
If you are having trouble loading your Ego trimmer string, there are a few possible causes.
1. The string is not wound in the correct direction.
The string should be wound around the spool in the direction indicated by the arrows on the spool. If the string is wound in the wrong direction, it will not feed properly.
2. The string is too thick.
The Ego trimmer is designed to use 0.065-inch diameter string. If you are using a thicker string, it will not fit properly in the spool.
3. The spool is not seated properly.
The spool must be seated properly in the trimmer head in order for the string to feed properly. Make sure that the spool is fully inserted into the head and that the release button is engaged.
4. The trimmer head is not closed properly.
The trimmer head must be closed properly in order for the string to feed properly. Make sure that the head is fully closed and that the release button is engaged.
5. The string is jammed.
If the string is jammed, you can try to clear it by pulling it out from the hole in the trimmer head. If the string is still jammed, you may need to remove the trimmer head and clear the jam manually.
6. The spool is damaged.
If the spool is damaged, you will need to replace it. You can purchase a new spool from a local hardware store or online.
7. The trimmer is not working properly.
If the trimmer is not working properly, you may need to take it to a qualified repair technician for service.
8. The string is not straight.
If the string is not straight, it can cause the trimmer to vibrate excessively. You can straighten the string by pulling it out from the hole in the trimmer head and then winding it back onto the spool in the opposite direction.
9. The string is too short.
If the string is too short, it will not reach the ground and will not be able to cut grass. You can add more string to the spool by winding it around the spool in the direction indicated by the arrows.
10. The string is wrapped too tightly around the spool.
This can prevent the string from feeding properly and can cause the trimmer to overheat. If the string is wrapped too tightly, you can loosen it by pulling it out from the hole in the trimmer head and then winding it back onto the spool in the opposite direction.
Ego Trimmer How To Load
To load EGO trimmer line, follow these steps:
- Unplug the trimmer from the power source.
- Locate the trimmer head.
- Press the release button on the trimmer head and pull it off.
- Cut two pieces of trimmer line to the desired length.
- Feed the trimmer line through the holes in the trimmer head.
- Wind the trimmer line around the spool in the trimmer head.
- Reattach the trimmer head to the trimmer.
- Plug the trimmer into the power source.
Your EGO trimmer is now ready to use.
People also ask about Ego Trimmer How To Load
How do I know when to replace the trimmer line on my EGO trimmer?
The trimmer line on your EGO trimmer should be replaced when it becomes worn or damaged. You can check the trimmer line by pulling on it. If the trimmer line breaks easily, it should be replaced.
What type of trimmer line should I use with my EGO trimmer?
You should use a trimmer line that is compatible with your EGO trimmer. The type of trimmer line that you use will depend on the model of your trimmer. You can find the recommended trimmer line for your model in the user manual.
How often should I lubricate my EGO trimmer?
You should lubricate your EGO trimmer every 25 hours of use. You can lubricate the trimmer by applying a few drops of oil to the trimmer head and the drive shaft.
