How to Open a Honda CR-V Bonnet
If you need to access the engine of your Honda CR-V, you’ll need to know how to open the bonnet. This DIY guide will show you how to do it in a few simple steps. Before you start, make sure that the engine is cool and that the car is parked on a level surface.
The bonnet release lever is located on the driver’s side of the footwell. Pull the lever towards you and the bonnet will pop up slightly. You can then reach up and pull the bonnet fully open. There is a safety catch on the bonnet that you need to release before you can open it fully. To release the safety catch, simply pull the lever towards you and then lift the bonnet up.
Once the bonnet is open, you’ll have access to the engine. Be careful not to touch any of the hot components, and make sure that you disconnect the battery before you start working on the engine. When you’re finished working on the engine, close the bonnet by pushing down on it until it latches. Make sure that the bonnet is fully closed and latched before you drive the car.
Locate the Bonnet Release Lever
The bonnet release lever for the Honda CR-V is typically located on the driver’s side of the footwell, near the bottom of the dashboard. It can be identified by a small, black lever with a bonnet symbol or the word “bonnet” written on it.
Steps to Locate the Bonnet Release Lever:
1. Open the driver’s door and sit in the driver’s seat.
2. Look down at the footwell area, near the bottom of the dashboard.
3. Locate the black lever with a bonnet symbol or the word “bonnet” written on it.
4. Test the lever by pulling it upwards. If it releases the bonnet latch, then you have found the correct lever.
Pull the Bonnet Release Lever
Locate the bonnet release lever inside the vehicle, usually on the driver’s side near the dashboard. The lever is typically marked with a symbol of a car bonnet or an arrow pointing upwards.
Pull the lever firmly to release the bonnet latch. You may hear a clicking sound as the latch disengages.
Once the latch is released, the bonnet will pop up slightly.
Lift the Bonnet
With the bonnet partially open, lift it further by hand from the center of the bonnet. Be careful not to touch the hot engine compartment.
Hold the bonnet open with the provided bonnet stay rod, which is usually located on the inside of the bonnet.
Now, you have successfully opened the bonnet of your Honda CR-V.
Bonnet Stay Rod Locations
| Driver’s Side | Passenger’s Side |
|—|—|
| Left side of the bonnet compartment | Right side of the bonnet compartment |
Find the Safety Latch and Lift
The safety latch for the hood of a Honda CR-V is located on the inside of the vehicle, near the driver’s side door. To find the safety latch, look for a small, black lever with a red handle. Once you have found the safety latch, pull it towards you and lift up on the hood. The hood will now be open.
Here are some additional tips for opening the hood of a Honda CR-V:
- If the hood is frozen shut, you can use a de-icer spray to help loosen it up.
- If you have trouble finding the safety latch, you can consult your vehicle’s owner’s manual for assistance.
- Once you have opened the hood, be sure to prop it up with the support rod before performing any work on the vehicle.
Here is a table summarizing the steps on how to open the hood of a Honda CR-V:
| Step | Description |
|---|---|
| 1 | Locate the safety latch on the inside of the vehicle, near the driver’s side door. |
| 2 | Pull the safety latch towards you and lift up on the hood. |
| 3 | Prop up the hood with the support rod before performing any work on the vehicle. |
Use the Prop Rod
To open your Honda CR-V bonnet using the prop rod, follow these steps:
1. Locate the Prop Rod
The prop rod is a thin, metal bar that is usually located in the trunk of your CR-V. It may be attached to the trunk lid or stored in a designated compartment.
2. Open the Trunk
Use your key or the trunk release button to open the trunk.
3. Retrieve the Prop Rod
Locate the prop rod and carefully remove it from its storage location.
4. Insert the Prop Rod into the Bonnet Release Bracket
Once you have the prop rod, locate the bonnet release bracket. This is a small, metal bracket located on the front of the CR-V, typically on the driver’s side near the grille. Carefully insert the prop rod into the bracket and ensure it fits snugly.
| Prop Rod | Bonnet Release Bracket |
|---|---|
 |
 |
Tip: If you have difficulty inserting the prop rod, try twisting it slightly to align it with the bracket.
Replace the Prop Rod
To replace the prop rod, you’ll need to purchase a new one that is specifically designed for your Honda CR-V. Once you have the new prop rod, follow these steps:
- Open the hood of your Honda CR-V.
- Locate the prop rod that is attached to the hood. It will be located near the front of the hood, on either the driver’s or passenger’s side.
- Remove the old prop rod by pulling it out of the bracket that is attached to the hood.
- Insert the new prop rod into the bracket on the hood.
- Close the hood of your Honda CR-V.
Here is a more detailed explanation of step 5:
When you close the hood of your Honda CR-V, the prop rod will automatically extend and hold the hood open. To release the hood, simply pull the release lever that is located on the inside of the hood, near the latch. The prop rod will then retract and the hood will close.
| Prop Rod Part Numbers | ||||||||
|---|---|---|---|---|---|---|---|---|
|
How to Open Honda CR-V Bonnet
Open the Bonnet
1. Locate the hood release lever:
It’s typically found on the driver’s side footwell or near the steering wheel.
2. Pull the lever:
Grab the hood release lever and pull it towards you.
3. Lift the hood:
With the lever pulled, lift the hood slightly.
4. Support the hood with the prop rod:
Once the hood is lifted, insert the prop rod into the designated notch to keep it open.
Close the Bonnet
1. Lift the bonnet:
Pull the hood release lever again to release the prop rod. Lift the bonnet fully.
2. Align the bonnet:
Position the bonnet evenly over the engine bay.
3. Lower the bonnet:
Slowly lower the bonnet until it’s about a foot from closing.
4. Engage the hood latch:
As the bonnet descends, you’ll hear a click as the hood latch engages.
5. Press firmly:
Once the hood latch is engaged, press down firmly on the center of the bonnet to completely close it.
6. Verify closure:
- Visual inspection: Ensure that the bonnet is flush with the fenders and no gaps are visible.
- Pressure test: Try to lift the bonnet again. If it remains closed, the latch is properly secured.
- Sound check: The bonnet should make a solid "thud" sound when fully closed. If you hear a rattling noise, ensure the latch is fully engaged.
- Security check: If equipped, verify that the bonnet lock is engaged and the key is removed.
Ensure the Bonnet is Latched Securely
Before attempting to open the bonnet, ensure that it is latched securely. This will prevent the bonnet from unexpectedly opening while driving, which could obstruct your vision or cause injury.
To check if the bonnet is latched securely, follow these steps:
| Step | Description |
|---|---|
| 1 | Locate the bonnet latch release lever inside the vehicle, typically on the driver’s side dashboard. |
| 2 | Pull the lever to release the bonnet latch. |
| 3 | Lift the bonnet slightly and check if it is latched by pressing down on the center of the bonnet. |
| 4 | If the bonnet does not latch securely, repeat steps 2 and 3 until the latch engages properly. |
Troubleshooting Tips
### 1. Check the Bonnet Release Lever
Ensure the bonnet release lever located inside the car is pulled up fully. If it’s stuck or loose, try gently pulling it up with your hand.
### 2. Locate the Emergency Release Cable
If the interior release lever is inoperable, locate the emergency release cable usually found under the dashboard or near the steering column. Pull the cable to unlock the bonnet.
### 3. Clean the Bonnet Latch
Dirt or debris can accumulate in the bonnet latch, preventing it from engaging properly. Clean the latch and its surroundings with a cloth or brush.
### 4. Lubricate the Bonnet Hinge
Applying a small amount of lubricant, such as WD-40 or silicone spray, to the bonnet hinge can help prevent sticking and make it easier to open.
### 5. Check the Bonnet Switch
The bonnet switch, located near the latch, detects when the bonnet is closed. A faulty switch may prevent the bonnet from releasing. Test the switch by bridging its terminals with a wire; if the bonnet opens, replace the switch.
### 6. Inspect the Fuse
A blown fuse labeled “Bonnet Release” or similar can prevent the bonnet from opening electrically. Check the fuse box and replace any blown fuses.
### 7. Reset the Battery
Disconnecting the battery for a few minutes can reset the electrical system, including the bonnet release mechanism. Reconnect the battery and try opening the bonnet again.
### 8. Seek Professional Help
If you’ve tried all the above troubleshooting steps and the bonnet remains stuck, it’s recommended to seek professional assistance from a mechanic or Honda dealership. They have specialized tools and knowledge to diagnose and resolve the issue safely.
Safety Precautions
Before attempting to open the bonnet of your Honda CR-V, it is essential to take the necessary safety precautions to prevent any potential hazards.
1. Park Safely
Ensure that your vehicle is parked on a stable and level surface. Engage the parking brake to prevent the vehicle from rolling.
2. Turn Off Engine
Turn off the engine and remove the key from the ignition to avoid any accidental starting when you open the bonnet.
3. Allow Engine to Cool
If you have recently driven your Honda CR-V, allow the engine to cool down sufficiently before opening the bonnet. This will prevent the risk of burns from hot components.
4. Identify Bonnet Release Lever
Locate the bonnet release lever, which is typically found under the dashboard on the driver’s side.
5. Pull Release Lever
Gently pull the bonnet release lever towards you to unlock the latch. You may hear a clicking sound.
6. Locate Secondary Latch
Once the primary latch is unlocked, locate the secondary latch at the front of the bonnet. This latch may vary depending on the model and year of your Honda CR-V.
7. Release Secondary Latch
Depending on the latch design, you may need to squeeze or pull it to release the bonnet.
8. Lift Bonnet
With the secondary latch released, carefully lift the bonnet upwards using the designated handle on the inside of the bonnet.
9. Use Bonnet Prop Rod
After lifting the bonnet, locate the bonnet prop rod, typically found in a designated storage area under the bonnet. Extend the prop rod and place it in the designated slot to hold the bonnet open securely.
How To Open Honda Crv Bonnet
Opening the bonnet of a Honda CR-V is a simple process that can be completed in a few easy steps.
- Locate the bonnet release lever inside the vehicle, usually on the driver’s side.
- Pull the lever to release the bonnet latch.
- Go to the front of the vehicle and lift the bonnet up.
- Secure the bonnet in the open position using the bonnet prop rod.
- To close the bonnet, simply lower it down and push on it until it latches.
Additional Information
Safety Precautions
Before opening the bonnet, make sure the vehicle is parked on a level surface and the parking brake is engaged. Allow the engine to cool down before opening the bonnet to avoid burns.
Bonnet Release Location
The bonnet release lever is typically located on the lower left side of the dashboard, near the driver’s footwell. It may be covered by a small panel or trim piece.
Bonnet Latch
The bonnet latch is located on the underside of the bonnet, near the front grille. When the bonnet release lever is pulled, the latch will release and the bonnet will pop up slightly.
Bonnet Prop Rod
The bonnet prop rod is a metal rod that is used to hold the bonnet open. It is usually located in the engine compartment, near the bonnet latch. To use the prop rod, simply insert it into the hole provided on the underside of the bonnet.
Closing the Bonnet
To close the bonnet, simply lower it down until it latches. You may need to push down on the bonnet slightly to ensure that it is fully closed.
Common Problems
If you are having difficulty opening the bonnet, there may be a problem with the bonnet release lever, latch, or prop rod. Inspect these components for any damage or obstructions. If you are still unable to open the bonnet, you may need to consult a mechanic.
How to Open Honda CR-V Bonnet
To open the Honda CR-V bonnet, follow these steps:
- Pull the bonnet release lever located inside the vehicle on the driver’s side.
- Locate the secondary bonnet latch under the front grille.
- Squeeze the release lever on the secondary latch and lift the bonnet.
- Prop the bonnet open using the bonnet stay.
People Also Ask About How to Open Honda CR-V Bonnet
How do I open a frozen Honda CR-V bonnet?
If the bonnet is frozen shut, use a de-icer spray or warm water to melt the ice around the latch.
Where is the bonnet release lever located on a Honda CR-V?
The bonnet release lever is located inside the vehicle on the driver’s side, near the left knee.
Can I open the Honda CR-V bonnet without a key?
Yes, the bonnet can be opened without a key using the secondary bonnet latch under the front grille.
