Struggling to dispense your favorite body wash due to a stubborn pump? Fear not, for unlocking the secrets of the elusive native body wash pump is within your grasp. This guide will empower you with the knowledge and techniques to conquer this seemingly insurmountable challenge, ensuring a smooth and satisfying bathing experience.
To begin your journey, gather your tools: a flathead screwdriver or butter knife, a pair of pliers, and a cloth. Carefully locate the small notch or indentation on the pump head, where the locking mechanism resides. Using the flathead screwdriver or butter knife, gently pry open the notch, taking care not to damage the surrounding plastic. Once the latch is released, the pump head should easily lift off, revealing the inner workings.
Next, inspect the pump mechanism. You may encounter a small spring or a plastic tab that locks the pump in place. Using the pliers, gently squeeze the tab or release the spring, allowing the pump to move freely. If the pump is still not dispensing, check for any blockages or debris that may be obstructing the flow. Use a cotton swab or a toothpick to gently remove any accumulated product or residue. Finally, reassemble the pump head by aligning the notches and pressing down firmly until it clicks into place.
Gathering the Necessary Tools
The first step in opening a native body wash pump is to gather the necessary tools. You will need:
– A pair of pliers
– A screwdriver
– A knife
– A hammer
Using a Pair of Pliers
Using a pair of pliers, grasp the top of the pump head and turn it counterclockwise. If the head does not turn easily, apply gentle pressure with the pliers. Continue turning until the head is completely removed.
Using a Screwdriver
Insert the tip of a screwdriver into the hole at the bottom of the pump head. Turn the screwdriver clockwise to loosen the screw. Once the screw is loose, remove it completely.
Using a Knife
Use a knife to cut the plastic ring that is holding the pump head in place. Be careful not to cut yourself.
Using a Hammer
If the pump head is still stuck, you can use a hammer to gently tap it loose. Place the hammer on the side of the pump head and tap it with a gentle force. Continue tapping until the head is loose.
Tool | Description |
---|---|
Pliers | Used to grip and turn the pump head |
Screwdriver | Used to loosen the screw that holds the pump head in place |
Knife | Used to cut the plastic ring that holds the pump head in place |
Hammer | Used to gently tap the pump head loose if it is stuck |
Locating the Locking Mechanism
Pin-Locking Mechanism
In this mechanism, a small plastic pin connects the pump to the base of the bottle. To unlock it, find the pin on either side of the pump base. Use a small tool like a paperclip or toothpick to push down on the pin. While holding the pin down, lift the pump head to separate it from the bottle.
Ring-Locking Mechanism
This mechanism features a small plastic ring around the base of the pump. To unlock it, locate the ring and turn it counterclockwise until it loosens. The pump head should then lift off easily.
Button-Locking Mechanism
Button-locking mechanisms involve a small button located on the top or side of the pump head. To unlock it, follow these steps:
- Identify the button: It is usually a small, round, or rectangular button.
- Press and hold the button: While holding the button down, lift the pump head upwards.
- Pull up the pump head: Continue holding the button and pull the pump head straight up to release it from the locking mechanism.
Tab-Locking Mechanism
Tab-locking mechanisms have a small plastic tab or lever on the side of the pump head. To unlock it, follow these steps:
- Locate the tab: Find the plastic tab on the pump head.
- Push down on the tab: Press down on the tab until it releases the pump head.
- Lift off the pump head: Lift the pump head straight up to remove it from the bottle.
How To Open Native Body Wash Pump
Using the Correct Technique
Using the correct technique is crucial when opening a native body wash pump. Here’s a detailed step-by-step guide:
-
Identify the Lock: First, locate the small lock or notch on the top of the pump. It may resemble a small button or lever.
-
Press and Turn: Gently press down on the lock with your thumb while simultaneously turning the pump clockwise.
-
Continue Turning: Continue turning the pump clockwise while maintaining pressure on the lock. You should feel a slight resistance as the pump disengages from the locked position.
-
Unlock the Pump: Once the pump is disengaged, you can release the lock and continue turning the pump until it opens fully.
-
Separate the Pump: Once the pump is open, gently pull it straight up to separate it from the bottle. Avoid twisting or bending the pump, as this could damage it.
Additional Tips:
- If the pump is particularly tight, try using a rubber band or a pair of pliers for better grip.
- If the pump is still not opening, check for any obstructions or dirt that may be preventing it from disengaging.
- Always refer to the specific instructions on the product packaging for any additional guidance or variations in the opening process.
Depressing the Lock Button
The majority of native body wash pump tops have a simple lock mechanism that prevents accidental dispensing. When you need to use the body wash, you must depress the lock button to unlock the pump. This button is usually located on the top of the pump, near the nozzle. To depress the lock button, simply push down on it with your thumb or finger until you hear a click. This will release the lock and allow you to dispense the body wash.
Here are some tips for depressing the lock button:
- Use your thumb or finger to push down on the lock button.
- Push down on the button until you hear a click.
- If the button is stuck, try using a flat-head screwdriver to pry it loose.
- Be careful not to press too hard on the button, as this could damage the pump.
If you are having trouble depressing the lock button, you can try the following:
Problem | Solution |
---|---|
The button is stuck | Use a flat-head screwdriver to pry it loose |
I can’t push down on the button | Use your thumb or finger to push down on the button |
The pump is damaged | Replace the pump |
Removing the Pump Head
The pump head is the top part of the native body wash bottle that you press to dispense the product. It is usually made of plastic and has a spring-loaded mechanism inside. To remove the pump head, follow these steps:
- Locate the release button or tab. This is usually located on the side of the pump head. It may be labeled with an arrow or have a small indentation.
- Press the release button or tab. This will release the catch that holds the pump head in place.
- Pull up on the pump head. The pump head should come off easily.
- If the pump head is stuck, you can try using a pair of pliers to gently pry it off. Be careful not to damage the pump head or the bottle.
- Once the pump head is removed, you can wash it with soap and water. This will help to remove any residue from the product.
- To reattach the pump head, simply align it with the opening of the bottle and press down until it clicks into place.
Here is a table summarizing the steps for removing the pump head:
Step | Description |
---|---|
1 | Locate the release button or tab. |
2 | Press the release button or tab. |
3 | Pull up on the pump head. |
4 | If the pump head is stuck, you can try using a pair of pliers to gently pry it off. |
5 | Once the pump head is removed, you can wash it with soap and water. |
6 | To reattach the pump head, simply align it with the opening of the bottle and press down until it clicks into place. |
Cleaning the Pump Components
Once the pump is disassembled, all of its components should be thoroughly cleaned to remove any dirt or residue that may have accumulated over time. Follow these steps to clean the pump components:
- Use a damp cloth to wipe down the exterior of the pump, including the base, handle, and spout.
- Remove the spring from the pump and clean it with soap and water.
- Clean the piston by removing it from the pump and wiping it down with a damp cloth.
- Clean the O-rings by removing them from the pump and wiping them down with a damp cloth.
- Clean the check valve by removing it from the pump and wiping it down with a damp cloth.
- Clean the dip tube by removing it from the pump and wiping it down with a damp cloth.
- Clean the pump body by removing it from the base and wiping it down with a damp cloth.
- Reassemble the pump in reverse order of disassembly, ensuring that all components are properly aligned and seated.
Component | How to Clean |
---|---|
Exterior | Wipe down with a damp cloth. |
Spring | Remove from pump and clean with soap and water. |
Piston | Remove from pump and wipe down with a damp cloth. |
O-rings | Remove from pump and wipe down with a damp cloth. |
Check valve | Remove from pump and wipe down with a damp cloth. |
Dip tube | Remove from pump and wipe down with a damp cloth. |
Pump body | Remove from base and wipe down with a damp cloth. |
Reassembling the Pump
Once the pump is cleaned, it is time to reassemble it. To do this, start by pulling out the stem.
Inserting the Stem
Align the stem with the pump head and push it down until it fits snugly. Ensure that the stem is inserted all the way and there are no gaps.
Attaching the Spring
Take the spring and place it inside the pump head, positioning it around the stem. The spring’s purpose is to create tension, helping the pump to dispense the body wash.
Inserting the Plunger
Align the plunger with the stem and push it down until it fits securely. The plunger is the component that draws the body wash up through the stem.
Attaching the Cap
Place the cap on top of the pump head and screw it securely. Ensure that the cap is tightly sealed to prevent leakage.
Inserting the Collar
Slip the collar over the cap and screw it into place. The collar secures the cap and ensures a leak-proof fit.
Testing the Pump
Once the pump is reassembled, test it by pumping it a few times. It should dispense body wash smoothly without any leaks or blockages.
Troubleshooting
If the pump is not working correctly, troubleshoot by checking the following:
Issue | Solution |
---|---|
Pump not dispensing body wash | Check if the stem is inserted properly. Ensure the spring is not damaged. |
Pump leaking | Tighten the collar and cap. Check for any cracks or damage to the pump components. |
Materials Required
To accomplish this task, you’ll need the following materials:
- A new body wash pump
- A Philips-head screwdriver (optional)
Step-by-Step Guide
- Locate the Pump Release Button: It is typically situated on the top of the bottle.
- Press and Hold the Button: Keep the button depressed while performing the subsequent steps.
- Twist Counterclockwise: Turn the pump in a counterclockwise direction while maintaining pressure on the button.
- Remove the Old Pump: As you continue twisting, the old pump will detach from the bottle.
- Clean the Connection Area: Wipe away any product residue from the bottle’s opening.
- Align the New Pump: Ensure that the new pump is properly oriented with the bottle’s opening.
- Insert and Screw: Push the new pump into the opening and start tightening it by hand.
- Use a Screwdriver (Optional): If hand-tightening proves difficult, you can use a Philips-head screwdriver to further secure the pump.
- Release the Button: Once the pump is secure, release the button.
- Test and Adjust: Dispense some body wash to test the pump’s functionality. If it dispenses too much or too little, you can slightly adjust the pump’s orientation or tighten it further.
Reattaching the Pump to the Bottle
- Lubricate the Pump Threads: Apply a thin layer of petroleum jelly or vegetable oil to the threads of the new pump.
- Insert the Pump into the Bottle: Align the pump with the bottle’s opening and push it down firmly.
- Tighten the Pump: Turn the pump clockwise to tighten it until it feels secure.
- Dispense Body Wash: Use the pump to dispense body wash and check for leaks.
- Wipe Away Excess Product: If there is any excess product around the pump, wipe it away with a clean cloth.
How to Open Native Body Wash Pump
Opening the pump on a Native Body Wash can be a little tricky, but it’s easy once you know how. Here are the steps:
-
Locate the small tab on the top of the pump. It will be on the side opposite the nozzle.
-
Press down on the tab and pull it towards you. This will release the pump from the bottle.
-
Lift the pump up and off of the bottle.
Once the pump is removed from the battle, you can add the Native body wash into the bottle.
People Also Ask About How To Open Native Body Wash Pump
How do you close the pump on a Native Body Wash?
To close the pump on a Native Body Wash, simply place the pump back on the bottle and push down until it clicks into place.
What do I do if the pump on my Native Body Wash is broken?
If the pump on your Native Body Wash is broken, you can contact Native for a replacement. You can also purchase a new pump from a retail store or online.
How do I refill a Native Body Wash bottle?
To refill a Native Body Wash bottle, simply remove the pump and add the new body wash to the bottle. Then, replace the pump and you’re good to go.