5 Easy Steps: How to Remove a Blade From a DeWalt Miter Saw

How to Remove a Blade From a DeWalt Miter Saw

Removing the blade from a Dewalt miter saw is a straightforward task that can be completed in just a few minutes. However, there are a few steps that must be followed to ensure that the job is done safely and correctly.

First, unplug the saw from the power outlet. Once the saw is unplugged, locate the blade guard and remove it. The blade guard is typically held in place by a few screws or bolts. Once the blade guard is removed, you will have access to the blade. Use a wrench to loosen the arbor nut that is holding the blade in place. Once the arbor nut is loosened, you can remove the blade from the saw.

When removing the blade from the saw, be sure to hold onto the blade guard with one hand to prevent it from falling. Once the blade is removed, inspect it for any damage. If the blade is damaged, it should be replaced before using the saw again.

Releasing the Blade Guard

Before you can remove the blade from your DeWalt miter saw, you’ll need to release the blade guard. To do this, follow these steps:

Locate the blade guard release lever. It’s usually located on the front or side of the saw, near the blade.
Push the release lever down. This will unlock the blade guard and allow you to move it out of the way.

Move the blade guard to the side. This will give you access to the blade.

Detailed Description of Step 2: Pushing the Release Lever Down

Pushing the release lever down is a critical step in disengaging the blade guard. Here’s a detailed description of how to do it:

Identify the release lever: It’s typically a small, black or red lever located near the blade guard.
Apply gentle pressure: Use your thumb or finger to gently push the lever down. Avoid using excessive force, as this could damage the lever or the saw.
Keep the lever down: Hold the lever down until you hear a click or feel the blade guard loosen. This indicates that the guard has been released.
Check for clearance: Once you’ve pushed the lever down, check if the blade guard moves freely. If it doesn’t, try gently wiggling the lever or applying slightly more pressure.

Removing the Blade Stabilizer Nut

To remove the blade stabilizer nut, you will need a 13mm wrench or socket. First, locate the blade stabilizer nut on the back of the miter saw. It is the large nut that holds the blade in place. Once you have located the nut, place the wrench or socket on the nut and turn it counterclockwise to loosen it. Be careful not to overtighten the nut, as this can damage the nut or the saw.

Once the nut is loose, you can remove the blade by pulling it straight towards you. Be careful not to drop the blade, as it is heavy and can cause injury.

Here is a table summarizing the steps on how to remove the blade stabilizer nut:

Step	Description
1	Locate the blade stabilizer nut on the back of the miter saw.
2	Place a 13mm wrench or socket on the nut and turn it counterclockwise to loosen it.
3	Once the nut is loose, remove the blade by pulling it straight towards you.

Lifing the Blade Out of the Arbor

Once you have removed the blade guard and loosened the arbor nut, you can begin lifting the blade out of the arbor. To do this, grasp the blade with both hands and pull it straight up. Be careful not to drop the blade, as it can be heavy.

If the blade is stuck in the arbor, you may need to use a pry bar to gently pry it loose. Once the blade is free, set it aside in a safe location.

Here are some additional tips for lifting the blade out of the arbor:

Make sure that the saw is turned off and unplugged before you begin.
Wear gloves to protect your hands from sharp edges.
Be careful not to drop the blade, as it can be heavy.
If the blade is stuck, use a pry bar to gently pry it loose.
Once the blade is free, set it aside in a safe location.

Cleaning and Inspecting the Blade

Once you’ve removed the blade from the saw, it’s important to clean and inspect it thoroughly. This will help you ensure that it’s in good condition and ready to use again. To clean the blade, use a cloth dampened with a mild detergent. Be sure to wipe down both sides of the blade, as well as the arbor hole. Once the blade is clean, inspect it for any damage. Look for cracks, chips, or bends. If you find any damage, do not use the blade. It could be dangerous.

Here are some additional tips for cleaning and inspecting your blade:

Use a soft cloth to avoid scratching the blade.
Wipe down the blade with a clean cloth before using it.
Inspect the blade for any damage before each use.
If you find any damage, do not use the blade.
Have your blade sharpened by a professional every 6 months to 1 year.
Store the blade in a dry place when not in use.

By following these tips, you can help ensure that your blade is in good condition and ready to use for years to come.

Additional Information

Here’s a table with some additional information about cleaning and inspecting your blade:

Tip	Description
Use a soft cloth	Avoid scratching the blade.
Wipe down the blade before using it	Remove any dirt or debris that could dull the blade.
Inspect the blade for damage before each use	Look for cracks, chips, or bends.
Do not use a damaged blade	It could be dangerous.
Have your blade sharpened by a professional every 6 months to 1 year	Keep the blade sharp for optimal performance.
Store the blade in a dry place when not in use	Prevent rust and corrosion.

Safety Precautions

Always unplug the miter saw before servicing it. Wear gloves and safety glasses to protect your hands and eyes.

Removing the Blade

1. Lock the Saw Arm

Place the saw arm at 90 degrees to the base and lock it in place using the knob or lever.

2. Locate the Blade Guard

The blade guard is located on the top of the saw blade. It covers the top portion of the blade for safety.

3. Lift the Blade Guard

Locate the lever or knob that lifts the blade guard. Lift it slowly and carefully.

4. Find the Arbor Nut

The arbor nut is located in the center of the saw blade. It holds the blade in place.

5. Loosen the Arbor Nut

Using a wrench or socket, carefully loosen the arbor nut counterclockwise.

6. Remove the Outer Flange

Once the arbor nut is loose, remove the outer flange by lifting it straight up.

7. Remove the Blade

With the outer flange removed, carefully grasp the blade by the sides and pull it straight out of the saw.

Reinstalling the Blade

1. Align the Keyway

The blade has a keyway that must align with the key on the arbor.

2. Insert the Blade

Insert the blade into the saw with the teeth facing the direction of rotation.

3. Replace the Outer Flange

Place the outer flange over the blade and align it with the arbor.

4. Tighten the Arbor Nut

Using the wrench or socket, carefully tighten the arbor nut clockwise.

5. Lower the Blade Guard

Slowly lower the blade guard into place.

6. Unlock the Saw Arm

Release the knob or lever that locked the saw arm.

Safety Equipment	Purpose
Gloves	Protect your hands from sharp edges
Safety Glasses	Protect your eyes from flying debris

Tightening the Blade Stabilizer Nut

The blade stabilizer nut is a crucial component that helps to secure the blade and prevent it from wobbling or vibrating excessively. Tightening this nut properly is essential for ensuring accurate cuts and extending the lifespan of the blade. Here are the steps to tighten the blade stabilizer nut:

1. Unplug the miter saw from the power source to prevent any accidental starting.
2. Locate the blade stabilizer nut, which is typically positioned behind the blade.
3. Insert the wrench into the nut and turn it clockwise until it is snug.
4. Hold the blade with one hand and use the other hand to tighten the nut further.
5. Check the blade’s movement by gently pushing it side-to-side. The blade should not wobble or move excessively.
6. If the blade still wobbles, tighten the nut slightly more.
7. Be careful not to overtighten the nut, as this can damage the blade or the arbor.
8. Refer to the following table for the recommended torque specifications for blade stabilizer nuts:

Blade Diameter	Torque (in-lbs)
7-1/4 inches	70
8-1/2 inches	90
10 inches	110
12 inches	130

Once the blade stabilizer nut is properly tightened, the blade should be securely held in place and ready for operation.

Testing the Miter Saw

1. Unplug the Saw:

Before starting any work, unplug the saw’s power cord from the electrical outlet for safety.

2. Depress the Trigger Lock:

Locate the trigger lock button on the saw’s handle and press it to prevent accidental triggering.

3. Remove the Blade Guard:

By unscrewing or flipping up the knob, lever, or latch mechanism, you can release and remove the blade guard that covers the blade.

4. Identify the Blade Bolt Wrench:

Find the blade bolt wrench that corresponds to the saw’s model. It’s usually stored onboard or nearby.

5. Locate the Blade Bolt:

Behind the blade, on the arbor, identify the blade bolt. It’s surrounded by a washer and typically has a hexagonal shape.

6. Insert the Wrench:

Insert the blade bolt wrench into the hexagonal recess of the blade bolt and ensure it’s properly seated.

7. Loosen the Blade Bolt:

Slowly rotate the wrench counterclockwise to loosen the bolt. Keep a firm grip on the saw to prevent wobbling.

8. Remove the Washer and Blade:

Once the bolt is loose, remove the washer behind it. Carefully detach the saw blade from the arbor and handle it with care to avoid sharp edges.

9. Replace the Blade:

Align the new saw blade with the arbor and insert it into place while simultaneously rotating the wrench clockwise to tighten the blade bolt.

10. Tighten the Blade Bolt:

Apply appropriate force while rotating the wrench clockwise to secure the blade bolt. Remember the manufacturer’s recommended tightening torque, which can be found in the saw’s user manual or on the bolt itself.

How To Remove Blade From Dewalt Miter Saw

Dewalt miter saws are popular power tools used for making precise cuts in wood. The blade is one of the most important components of a miter saw, and it needs to be replaced occasionally to maintain optimal performance. Removing the blade from a Dewalt miter saw is a relatively simple process that can be completed in a few minutes.

To remove the blade from a Dewalt miter saw, you will need a 17mm socket wrench or a 13mm Allen wrench. First, unplug the saw from the power outlet. Next, locate the blade guard and remove it by loosening the two screws that hold it in place. Once the blade guard is removed, you will be able to see the blade. Insert the socket wrench or Allen wrench into the center of the blade and loosen the bolt that holds it in place.

Once the bolt is loose, you can remove the blade by pulling it straight up. Be careful not to touch the sharp edges of the blade. Once the blade is removed, you can replace it with a new one. To do this, simply insert the new blade into the saw and tighten the bolt that holds it in place. Finally, replace the blade guard and tighten the screws that hold it in place.