Your Frigidaire water filter is a crucial component, ensuring you access clean, healthy water. However, replacing it regularly is essential to maintain its effectiveness. If you’ve been putting off changing your filter, fret not; the process is straightforward and requires minimal effort. Contrary to popular belief, you won’t need any tools or professional assistance. In this guide, we’ll walk you through the simple steps to remove your Frigidaire water filter, ensuring you have a steady supply of fresh, filtered water.
Before embarking on this task, locate your refrigerator’s water filter housing. It’s typically found either behind the refrigerator’s grille or inside the refrigerator compartment. Once you’ve identified the housing, the first step is to shut off the water supply to your refrigerator. This is a crucial safety measure to prevent water from spilling during the filter replacement process. You’ll find the water shut-off valve behind the refrigerator, usually near the bottom. Simply turn the valve clockwise to close it. Next, locate the filter cap on the housing and turn it counterclockwise to loosen it. Once it’s loose enough, pull it straight out to detach it from the housing. With the cap removed, gently pull the old filter straight down to disengage it from the housing.
Once the old filter is out, it’s time to insert the new one. Before installing the new filter, apply a small amount of petroleum jelly to the O-rings on both ends of the filter. This will help create a tight seal and prevent leaks. Align the new filter with the housing and push it straight up until it fits snugly. Make sure it’s securely in place. Next, replace the filter cap and turn it clockwise to tighten it. The final step is to turn the water supply back on by turning the valve counterclockwise. Check for any leaks around the filter housing and cap. If everything seems fine, you’re all set! Your Frigidaire refrigerator is now equipped with a fresh water filter, ensuring you and your family have access to clean, refreshing water.
Removing the Water Filter Compartment
To remove the water filter compartment on your Frigidaire refrigerator, follow these steps:
Locate the Water Filter Compartment
The water filter compartment is typically located inside the refrigerator, on the upper right or left-hand side, near the top. Look for a small, rectangular or round compartment with a handle or a button.
Disengage the Handle or Button
If the compartment has a handle, simply pull it down to disengage the filter compartment. If it has a button, press the button while pulling down on the compartment to release it.
Pull Out the Compartment
Once the handle or button is disengaged, gently pull out the water filter compartment. It should slide out easily. Be careful not to spill any water that may have collected in the compartment.
Remove the Old Filter
Once the compartment is removed, you can remove the old water filter. To do this, simply twist the filter counterclockwise until it becomes loose. Pull the filter straight out of the compartment.
Insert the New Filter
Take the new water filter and insert it into the compartment. Make sure that the filter is properly aligned and that the arrow on the filter is pointing towards the bottom of the compartment.
Twist the Filter into Place
Twist the filter clockwise until it is snug. Do not overtighten the filter.
Reinsert the Compartment
Gently slide the water filter compartment back into the refrigerator, making sure that it is properly seated.
Reset the Filter Indicator Light (if applicable)
Some Frigidaire refrigerators have a filter indicator light that will come on when the filter needs to be replaced. If your refrigerator has this light, you will need to reset it after replacing the filter.
To reset the filter indicator light, press and hold the “Filter Reset” button for 5 seconds. The light should turn off.
Locating the Water Filter
Depending on your Frigidaire refrigerator model, the water filter can be positioned in two primary locations: inside the refrigerator compartment or behind the grille at the bottom of the refrigerator.
Inside the Refrigerator Compartment:
1. Open the refrigerator door and locate the upper right-hand corner.
2. Find the removable air filter grille or cover and detach it by pressing the tabs or release button.
3. Behind the grille, you will find the water filter cartridge. It is typically held in place by a twist-and-lock mechanism.
Behind the Grille at the Bottom of the Refrigerator:
| Model Type | Location |
|---|---|
| Top Freezer | Behind the bottom grille, accessed from the front of the refrigerator. |
| Bottom Freezer | Behind the bottom grille, accessed from the rear of the refrigerator. |
| French Door | Inside the refrigerator compartment, behind a removable panel in the top right corner. |
4. Locate the grille at the bottom of the refrigerator, typically spanning the width of the appliance.
5. Carefully remove the grille by pressing on the release tabs or levers.
6. The water filter cartridge will be accessible behind the grille, typically connected to water lines.
Twisting the Filter Counterclockwise
Step 1: Locate the filter. The water filter is typically located in the lower right corner of the refrigerator. It is usually covered by a small plastic panel.
Step 2: Remove the panel. Use a flathead screwdriver or your fingernail to pry the panel off. The panel is usually held in place by two small tabs.
Step 3: Twist the filter. Once the panel is removed, you will see the water filter. Grip the filter and twist it counterclockwise. The filter will release from the refrigerator.
Tips:
| Tip | Details |
|---|---|
| Use a wrench. | If you have difficulty twisting the filter by hand, you can use a wrench to help. |
| Turn off the water supply. | It is a good idea to turn off the water supply before changing the filter. This will prevent water from leaking out when the filter is removed. |
| Replace the filter every 6 months. | The water filter should be replaced every 6 months to ensure that your refrigerator is dispensing clean, fresh water. |
Pulling the Filter Downward
Once you have cleared the path by removing the grille, you can proceed to pull the water filter downward. Grasp the filter firmly with one hand and gently pull it straight down. You may need to apply a bit of force as the filter may be slightly stuck in place due to mineral deposits or buildup. Avoid using excessive force, as you do not want to damage the filter or the refrigerator’s internal components.
As you pull the filter down, observe its movement. It should slide smoothly out of the housing. If you encounter any resistance or the filter seems to be stuck, stop pulling and check if there are any obstructions or debris that may be preventing its removal. Remove any obstructions and try pulling the filter down again.
If the filter still does not come out easily, you can try twisting it slightly back and forth while pulling it down. This can help loosen any mineral deposits or buildup that may be holding the filter in place. Be careful not to overtwist the filter, as you could damage it or the refrigerator’s internal components.
Installing the New Water Filter
Once you have removed the old filter, you can install the new one. To do this, simply insert the new filter into the housing and twist it clockwise until it is snug. Be sure not to overtighten the filter, as this can damage the housing.
Things you will need:
– New water filter
– Adjustable wrench or pliers
Instructions:
1. Turn off the water supply to the refrigerator.
2. Open the refrigerator door and locate the water filter housing.
3. Turn the filter housing counterclockwise to remove it.
4. Remove the old filter from the housing.
5. Insert the new filter into the housing and turn it clockwise until it is snug. Be sure not to overtighten the filter.
6. Turn on the water supply to the refrigerator and check for leaks.
7. Reset the filter indicator light by pressing and holding the “Filter Reset” button for 3 seconds.
After you have installed the new water filter, be sure to reset the filter indicator light. This will help you keep track of when it is time to replace the filter again.
Aligning the Filter with the Compartment
- Locate the water filter compartment on your Frigidaire refrigerator. It’s usually found on the top or bottom of the fridge.
- Open the compartment by pressing the release button or latch.
- Remove the old water filter by turning it counterclockwise and pulling it straight out.
- Align the new water filter with the slots in the compartment. The filter should fit snugly into place.
- Push the filter all the way into the compartment until it clicks into place.
- **Reset the water filter indicator light:** Press and hold the “Filter” button for 3 seconds, or follow the instructions on your refrigerator’s display panel. The light will turn off to indicate that the filter is active.
Tips:
| Tip | Description |
|---|---|
| Lubricate the O-rings | Apply a small amount of food-grade lubricant to the O-rings on the new filter to ensure a proper seal. |
| Check for leaks | After replacing the filter, run water through the dispenser and check for any leaks around the compartment. |
| Replace the filter regularly | It’s recommended to replace your Frigidaire water filter every 6 months or as indicated by the filter indicator light. |
Twisting the Filter Clockwise
If your Frigidaire refrigerator’s water filter is located in the top grille, you’ll need to twist it clockwise to remove it.
To do this:
1. Unplug the refrigerator.
2. Locate the water filter housing in the top grille of the refrigerator.
3. Grip the filter housing and twist it counterclockwise to loosen it.
4. Pull the filter housing down to remove it from the refrigerator.
5. Twist the water filter clockwise to loosen it from the filter housing.
6. Pull the water filter out of the filter housing.
Here is a table summarizing the steps for removing a Frigidaire water filter by twisting it clockwise:
| Step | Description |
|---|---|
| 1 | Unplug the refrigerator. |
| 2 | Locate the water filter housing in the top grille of the refrigerator. |
| 3 | Grip the filter housing and twist it counterclockwise to loosen it. |
| 4 | Pull the filter housing down to remove it from the refrigerator. |
| 5 | Twist the water filter clockwise to loosen it from the filter housing. |
| 6 | Pull the water filter out of the filter housing. |
Resetting the Filter Indicator Light
If you have replaced the water filter and the filter indicator light is still on, you will need to reset the filter indicator light. To reset the filter indicator light:
-
Press and hold the Water Filter button for 5 seconds.
-
The filter indicator light will flash rapidly for a few seconds and then turn off.
-
The filter indicator light will now be reset and will turn on again when it is time to replace the water filter.
NOTE: If the filter indicator light does not turn off after following the above steps, there may be a problem with the water filter or the refrigerator. In this case, you will need to contact a qualified appliance repair technician.
Here is a table summarizing the steps to reset the filter indicator light:
| Step | Instructions |
|---|---|
| 1 | Press and hold the Water Filter button for 5 seconds. |
| 2 | The filter indicator light will flash rapidly for a few seconds and then turn off. |
| 3 | The filter indicator light will now be reset and will turn on again when it is time to replace the water filter. |
Troubleshooting Common Issues
Filter Won’t Twist Off
If the filter is stuck and won’t twist off, try one of the following methods:
- Use a pair of pliers or a strap wrench to get a better grip on the filter.
- If the filter is still stuck, try soaking it in vinegar for a few hours to loosen any mineral buildup.
- Use a butter knife or other flat object to gently pry the filter loose.
Water Leaking From Filter Head
If water is leaking from the filter head, it is likely due to one of the following issues:
| Possible Cause | Solution |
|---|---|
| The O-ring on the filter is not seated properly. | Remove the filter and reinsert it, making sure that the O-ring is seated correctly. |
| The filter head is cracked or damaged. | Replace the filter head. |
| The water line is not connected properly. | Disconnect the water line and reconnect it, making sure that it is tight. |
Maintaining Your Frigidaire Water Filter
1. Locate the water filter
The water filter is typically located in the bottom of the refrigerator, behind the bottom grille. Look for a blue cap or knob.
2. Turn off the water supply
Locate the water supply valve, which is usually located behind the refrigerator. Turn the valve clockwise to shut off the water.
3. Remove the old filter
Grasp the water filter and turn it counterclockwise to remove it. Some filters may have a release button that needs to be pressed first.
4. Lubricate the O-rings
Apply a small amount of food-grade lubricant to the O-rings on the new filter. This will help to prevent leaks.
5. Insert the new filter
Align the new filter with the housing and push it into place. Turn it clockwise to tighten it.
6. Turn on the water supply
Turn the water supply valve counterclockwise to turn on the water. Check for leaks around the filter.
7. Reset the filter indicator
Some Frigidaire refrigerators have a filter indicator light. If the light is on, press and hold the filter reset button for 5 seconds to reset it.
8. Run water through the filter
Run water through the dispenser for a few minutes to flush out any air or debris.
9. Check the water quality
Taste the water from the dispenser to make sure it is clean and free of any impurities.
10. Replace the filter regularly
Frigidaire water filters should be replaced every 6 months or 300 gallons of use. The actual lifespan of a filter will vary depending on the quality of your water. To keep your water tasting its best and flowing freely, it’s important to change the filter regularly.
| Refrigerator Model | Filter Type |
|---|---|
| Frigidaire FRS26H5ASB | PureSource Ultra II |
| Frigidaire FGHC2331PF | UFL-GB1000 |
How to Remove Frigidaire Water Filter
Frigidaire water filters are designed to remove impurities and improve the taste and smell of your water. Over time, water filters can become clogged with sediment and other contaminants which can reduce their effectiveness. It’s important to replace your Frigidaire water filter every 6 months to ensure that you’re drinking clean, healthy water.
To remove the water filter, follow these simple steps:
- Turn off the water supply to the refrigerator. This is usually done by turning the water valve behind the refrigerator to the “off” position.
- Find the water filter housing. The water filter housing is typically located on the back or side of the refrigerator. It will be a plastic housing with a blue cap.
- Twist the filter housing cap to unlock it. Be sure to hold onto the housing with your other hand so that it doesn’t fall off.
- Pull the old water filter straight out of the housing. Discard the old filter.
- Insert the new water filter into the housing. Make sure that the filter is aligned properly and that the o-rings are in place.
- Twist the filter housing cap to lock it into place. Turn the water supply back on and check for leaks.
People Also Ask About How to Remove Frigidaire Water Filter
Where is the water filter located on a Frigidaire refrigerator?
The water filter is typically located on the back or side of the refrigerator. It will be a plastic housing with a blue cap.
How often should I change my Frigidaire water filter?
Frigidaire recommends changing the water filter every 6 months.
What happens if I don’t change my Frigidaire water filter?
If you don’t change your Frigidaire water filter, it can become clogged with sediment and other contaminants. This can reduce the effectiveness of the filter and lead to decreased water quality.
Can I use a different brand of water filter in my Frigidaire refrigerator?
No, you should only use Frigidaire-branded water filters in your Frigidaire refrigerator.
