If your GE washer is experiencing issues with its deep fill function, a reset may be necessary to restore its proper operation. While the deep fill option allows you to add more water to your wash cycle, a malfunctioning deep fill setting can lead to an inefficient or unsatisfactory wash. Fortunately, resetting your GE washer’s deep fill is a straightforward process that can be completed in a few simple steps. Whether you’re experiencing water level issues, unexpected pauses during deep fill cycles, or other related concerns, understanding how to reset this feature will help you troubleshoot and maximize the performance of your washer.
Before proceeding with the reset, it’s essential to gather any necessary materials and ensure your safety. Read through the instruction manual or consult GE’s official support website to confirm the specific steps for your washer model. Safety precautions include unplugging the washer from its power source and ensuring that the water supply valves are closed. Once you have prepared and verified the necessary steps, you can proceed with the reset process. Carefully follow the instructions provided by GE to ensure a successful reset and avoid any potential damage or improper operation.
After completing the reset, reconnect your washer to the power source and water supply, and run a test wash cycle to verify that the deep fill function is operating correctly. If the issue persists or you encounter any unexpected behavior, it’s recommended to contact GE’s customer support for further assistance. They can provide additional troubleshooting tips, schedule a repair appointment if necessary, and ensure that your washer is functioning optimally. Regular maintenance and proper use will help prolong the life of your GE washer, and understanding how to reset the deep fill function is a valuable skill for any homeowner who wants to maintain their appliance in good working order.
Disabling Deep Fill Once a Cycle Begins
Once you’ve started a washing cycle with the Deep Fill option enabled, there’s no way to disable it mid-cycle. The washing machine will continue to add water to the tub until it reaches the maximum level set for Deep Fill.
However, there are a few things you can do to minimize the amount of water used in the cycle:
- If you’re using a liquid detergent, add it to the dispenser drawer instead of pouring it directly into the tub. This will help to prevent the detergent from sudsing up too much and causing the machine to add more water.
- Use a shorter wash cycle. The shorter the cycle, the less time the machine will have to add water.
- Choose a lower spin speed. A lower spin speed will extract less water from the clothes, which means the machine will need to add less water to rinse them.
Tips for Choosing the Right Amount of Water
The amount of water you need for a washing cycle depends on the size of the load and the type of fabric you’re washing. Here are some general guidelines:
| Load Size | Amount of Water |
|---|---|
| Small | 2-3 gallons |
| Medium | 3-4 gallons |
| Large | 4-5 gallons |
If you’re not sure how much water to use, it’s always better to err on the side of caution and add less. You can always add more water if needed, but you can’t take it away once it’s been added.
Entering GE Washer Diagnostics Mode
To access the GE washer diagnostics mode, follow these steps:
- Unplug the washer from the power outlet.
- Wait 30 seconds.
- Plug the washer back into the power outlet.
- Within 15 seconds, press and hold the “Diagnostic Test Results” button.
- Continue holding the button for 3 seconds.
- Release the button and wait for the washer to enter diagnostic mode.
Checking the Component’s Status
Once you are in the diagnostic mode, you can check the status of various components of your washer. Here’s how to check the status of a specific component:
- Press the “Diagnostic Test Results” button repeatedly until the desired component is displayed on the screen.
- The component status will be displayed as either “Pass” or “Fail.”
- If the component fails the test, you will need to replace it.
Exiting Diagnostics Mode
To exit diagnostics mode, press the “Diagnostic Test Results” button. The washer will return to normal operation.
Using the GE App to Reset Deep Fill
The GE Appliances app provides an easy and convenient way to reset the Deep Fill option on your washer. Follow these steps:
1. Download the GE Appliances app from the App Store or Google Play.
2. Create an account or sign in to your existing account.
3. Select your washer from the list of connected appliances. If your washer is not listed, follow the app’s instructions to add it.
4. Tap the “Settings” tab.
5. Scroll down and tap “Deep Fill.”
6. Toggle the Deep Fill switch to the “Off” position.
7. Tap “Save.”
Alternatively, you can reset the Deep Fill option through the washer’s control panel:
| Model | Reset Instructions |
|---|---|
| GE Profile Washer | Press and hold the “Deep Fill” button for 3 seconds. |
| GE Front-Load Washer | Press and hold the “Water Level” button for 3 seconds. |
| GE Top-Load Washer | Press and hold the “Wash Plate” button for 3 seconds. |
Factory Resetting the GE Washer
If your GE washer is experiencing issues or not performing as it should, you may need to factory reset it. Factory resetting the washer will restore it to its original settings and may resolve any issues you are encountering.
Steps to Factory Reset a GE Washer:
- Unplug the washer from the power outlet.
- Wait one minute.
- Plug the washer back into the power outlet.
- Within 30 seconds of plugging the washer back in, press and hold the following buttons simultaneously for about 5 seconds:
- For top-load washers: Rinse + Hold & Soil Level buttons.
- For front-load washers: Temp & Spin Speed buttons.
- The washer will go through a reset cycle, which may take several minutes.
- Once the reset cycle is complete, the washer should be restored to its factory default settings.
Shutting Off the Water Supply
To avoid any water damage during the reset process, it’s crucial to turn off the water supply to your GE washer. Here’s a detailed step-by-step guide on how to do it:
-
Locate the Water Inlet Valves
Identify the two water inlet valves located at the back of your washer. One valve is for cold water, and the other is for hot water.
-
Turn the Valves Clockwise
Using a pair of pliers or a wrench, grasp the handle of each water inlet valve and turn it clockwise. Turn until the valves are completely closed, and no more water flows.
-
Check for Leaks
Once the valves are closed, open a cold water tap anywhere in your house. Check the water inlet valves on the washer to ensure there are no leaks. If you notice any leaks, tighten the valves further or contact a plumber.
-
Close the Tap
After checking for leaks, close the cold water tap you opened earlier.
-
Disconnect the Water Hoses
Use a pair of pliers to disconnect the water hoses from the water inlet valves on the washer. Be careful not to damage the hoses.
Unplugging the Washer
Step 1: Locate the Power Cord
Find the power cord connected to the back of the washer. It’s typically a thick, black or white cord.
Step 2: Unplug the Cord
Reach down and firmly grasp the plug. Pull straight up to remove it from the electrical outlet. Do not pull on the cord, as this could damage the wires.
Step 3: Wait 5-10 Minutes
Leave the washer unplugged for at least 5-10 minutes. This allows time for any stored electricity to dissipate.
Step 4: Check the Power
After waiting, plug the washer back into the outlet. Make sure the cord is securely seated in the socket.
Step 5: Turn on the Washer
Press the power button to turn the washer back on. This should reset the control system and clear any previous settings.
Step 6: Troubleshooting the Power Connection
If the washer doesn’t power up after being plugged in, try the following:
| Problem | Solution |
|---|---|
| Outlet not getting power | Check if other appliances are working in the same outlet. Try plugging the washer into a different outlet. |
| Power cord damaged | Inspect the power cord for any visible damage. If it’s frayed or broken, replace it before plugging the washer back in. |
| Circuit breaker tripped | Locate the electrical panel and check if any circuit breakers have tripped. Reset the tripped breakers. |
Pressing the Power and Start/Pause Buttons
To reset your GE washer using this method, follow these steps:
- Unplug the washer from the power outlet.
- Wait 60 seconds.
- Press and hold the Power button for 3 seconds.
- While holding the Power button, press and release the Start/Pause button 3 times.
- Release the Power button.
- Plug the washer back into the power outlet.
- Press the Power button to turn on the washer.
- The washer will now be reset.
This method is only applicable to GE washers with a digital display.
Additional Information
If you are still having trouble resetting your GE washer, you can consult the user manual or contact GE customer support.
Turning the Dial to Select Diagnostics Mode
To reset your GE washer’s Deep Fill option, you’ll need to enter diagnostics mode. Here are the steps:
.
1. Unplug your washer from the power outlet.
2. Wait 60 seconds.
3. Plug your washer back into the power outlet.
4. Turn the dial to select “Diagnostics Mode”. The dial is located on the control panel of your washer.
5. Press and hold the “Start/Pause” button for 3 seconds.
6. Release the “Start/Pause” button.
7. The washer will enter diagnostics mode. The “Clean Washer” light will blink.
8. Turn the dial to select the “Deep Fill” option.The “Deep Fill” option is located in the “Utilities” menu. To select it, turn the dial until the “Deep Fill” option is highlighted on the display screen.
Use the + and – buttons to adjust the Deep Fill setting. The Deep Fill setting can be adjusted from “Off” to “Extra Deep”. The default setting is “Medium”.
9. Press the “Start/Pause” button to save the changes.
10. The washer will exit diagnostics mode. The “Clean Washer” light will turn off.
11. Your GE washer’s Deep Fill option is now reset.
Resetting Deep Fill Settings in Diagnostics Mode
Resetting the deep fill settings using the diagnostics mode requires a few specific steps. Follow these instructions carefully to ensure a successful reset:
1. Ensure that the washer is empty.
2. Hold the “Deep Fill” button for 5 seconds.
3. Turn the cycle knob one click clockwise and then one click counterclockwise.
4. Press the “Start/Pause” button and hold it for 3 seconds.
5. Release the “Start/Pause” button and turn the cycle knob clockwise until “DIAGS” appears on the display.
6. Press the “Start/Pause” button again.
7. Turn the cycle knob until “FF” appears on the display.
8. Press the “Start/Pause” button and hold it for 5 seconds.
9. The display will show a series of numbers and letters. This is the diagnostic code. To reset the deep fill settings, look for the code that corresponds to “Deep Fill” in the following table:
| Code | Setting |
|---|---|
| F01 | Deep Fill enabled |
| F02 | Deep Fill disabled |
10. Press the “Deep Fill” button to toggle the setting between “enabled” and “disabled”.
11. Once the setting has been changed, press the “Start/Pause” button to exit diagnostics mode.
How To Reset GE Washer Deep Fill
Resetting a GE washer with a Deep Fill option is a simple process that can be done in just a few steps:
- Unplug the washer from the power outlet.
- Wait 60 seconds.
- Plug the washer back into the power outlet.
- Turn on the washer and select the Deep Fill option.
The washer will now fill with water to the Deep Fill level.
People Also Ask About How To Reset GE Washer Deep Fill
How do I reset my GE Profile washer?
To reset your GE Profile washer, follow the steps outlined above.
How do I turn off the Deep Fill option on my GE washer?
To turn off the Deep Fill option on your GE washer, simply press the Deep Fill button once to deselect it.
I tried resetting my GE washer, but the Deep Fill option is still not working.
If you have tried resetting your GE washer and the Deep Fill option is still not working, there may be a problem with the washer itself. Contact a qualified appliance repair technician to diagnose and repair the problem.
