7 Steps To Safely Tension A Garage Door Spring

Garage door spring

The tension of a garage door spring is crucial for the smooth and safe operation of your garage door. An improperly tensioned spring can cause a host of problems, including difficulty opening or closing the door, premature wear and tear on the opener, and even a snapped spring. In this comprehensive guide, we will delve into the intricacies of garage door spring tension, providing step-by-step instructions on how to adjust it correctly.

Before embarking on this task, it is essential to understand the different types of garage door springs. The most common are extension springs, which run parallel to the track, and torsion springs, which are mounted above the door opening. Once you have identified the type of spring you have, you can proceed to the adjustment process.

Adjusting the tension of an extension spring involves using a winding bar to turn the cone-shaped pulleys at the ends of the spring. Turning the pulley clockwise increases the tension, while turning it counterclockwise decreases the tension. For torsion springs, you will need to loosen the set screws that hold the spring in place, then use a winding bar to turn the center shaft of the spring. Again, turning clockwise increases tension, while turning counterclockwise decreases it. As you adjust the tension, observe the movement of the door and make any necessary fine-tuning until the door opens and closes smoothly.

Identifying the Different Types of Garage Door Springs

Garage door springs are crucial components that balance the door’s weight, enabling it to open and close smoothly. Various types of springs are employed in garage doors, each catering to specific needs and applications. Understanding these different types is essential for proper maintenance and troubleshooting.

Extension Springs

Appearance: Extension springs resemble stretched-out coils. They are mounted horizontally above the door and extend as the door opens.

Mechanism: Extension springs store energy as they are stretched. When the door opens, they pull the door up, and when it closes, they recoil to assist in lowering the door.

Common Applications: Extension springs are commonly found in residential garage doors, especially those with a single or double-car capacity. They are relatively inexpensive and straightforward to install or replace.

Table: Extension Spring Characteristics

Characteristic	Description
Coil Diameter	Determines the amount of force the spring can generate
Coil Length	Affects the range of motion and lift capacity
Material	Usually made of steel or galvanized steel for durability

Gathering Essential Tools and Safety Gear

To ensure a safe and efficient garage door spring tensioning process, it is crucial to gather the necessary tools and safety gear. Here’s a detailed list of the essential items you’ll need:

Safety Gear:

Safety Glasses: Protect your eyes from flying debris or sparks.
Work Gloves: Shield your hands from sharp edges or pinched fingers.
Safety Mask: Prevent inhalation of dust or chemicals released during the process.
Sturdy Footwear: Wear closed-toe shoes with good grip to prevent slips or falls.
Ear Plugs or Ear Muffs: Protect your hearing from loud noises during spring tensioning.

Tools:

Tool	Purpose
Wrench or Socket Set	Adjusting bolts and nuts.
Ladder	Access to the garage door springs.
Spring Tension Tool	Reducing tension on the springs.
Lubricant	Lubricating springs and components.
Flashlight	Illuminating dark areas.

Disconnecting Electricity to the Door Operator

Before performing any maintenance or adjustment on your garage door spring, it’s crucial to disconnect the electricity supply to the door operator to prevent accidental activation.

Identifying the Electrical Panel

Locate the electrical panel supplying power to the garage door operator. It is typically found near the garage door opener unit, usually on the ceiling or wall.
Shutting Off the Circuit Breaker or Fuse

Once you have identified the electrical panel, isolate the circuit breaker or fuse dedicated to the garage door opener. Flip the circuit breaker to the “OFF” position or remove the fuse from its socket.
Verifying Power Disconnection

After isolating the circuit breaker or fuse, operate the garage door opener’s remote control or wall button. If the door does not respond, it indicates that the power has been successfully disconnected.

Before proceeding with the spring tension adjustment, ensure you have a flashlight or headlamp to illuminate the work area and a step stool or ladder to reach the springs safely.

Releasing Tension from the Existing Spring

Before you can remove the old spring, you need to release the tension from it. Here’s how:

Gather your tools. You will need a pair of pliers, a winding bar, and a C-clamp.
Open the garage door halfway. This will give you enough room to work safely.
Locate the spring. The spring is located on the side of the garage door opener. It is a long, metal coil with a hook on each end.
Secure the spring. Use the C-clamp to secure the spring in place. This will prevent it from moving when you release the tension.
Insert the winding bar. Insert the winding bar into the hole in the end of the spring.
Turn the winding bar counterclockwise. Slowly turn the winding bar counterclockwise until the tension is released from the spring.
Check the spring. Once the tension is released, the spring will be loose. You can now remove it from the garage door opener.

Replacing the Tension Spring

1. Safety First

Before you start, gather the necessary tools and ensure you have someone to assist you. Wear safety glasses, gloves, and appropriate clothing to protect yourself from any potential hazards.

2. Identify the Spring Type

Different garage doors use different types of springs. Identify the spring type you need by consulting your garage door’s manual or by contacting a professional.

3. Unwind the Spring

Use a winding bar or a spring tool to slowly and carefully unwind the old spring. Do this by inserting the tool into the spring and turning it counterclockwise gradually. Release the spring slowly to avoid any sudden movements.

4. Install the New Spring

Position the new spring in place and wind it in the opposite direction of unwinding. Use the same tool, but this time turn it clockwise to tighten the spring. Ensure the spring is adequately aligned and positioned.

5. Reconnect the Cables and Pulley

Attach the spring ends to the corresponding cables and the pulley. Ensure all the cables are in the proper position and adjusted to maintain proper spring tension. Use appropriate tools, such as a cable hook or pliers, to secure the cables.

Spring Type	Diameter	Length
Torsion Spring	1-1/4 inches (32 mm) to 2 inches (51 mm)	10 feet (3 m) to 15 feet (4.6 m)
Extension Spring	1/2 inch (13 mm) to 1-1/8 inches (29 mm)	18 inches (460 mm) to 36 inches (910 mm)

Winding the New Tension Spring

Once you have selected and purchased a new tension spring that is compatible with your garage door, you can proceed to wind it. Here are the steps you need to take:

1. Place the spring on the winding cone. The winding cone is a tool that helps to keep the spring aligned and prevents it from kinking as you wind it.

2. Insert the winding bar into the hole in the center of the spring. The winding bar is a long, thin rod that is used to turn the spring as you wind it.

3. Secure the winding bar in place. There is usually a small screw or bolt that you can tighten to secure the winding bar in place.

4. Begin winding the spring. Turn the winding bar in a clockwise direction to wind the spring. Wind the spring until the desired tension is reached.

5. Secure the spring. Once the spring is wound to the desired tension, you need to secure it. This can be done by tightening the set screw on the winding cone.

6. Lubricate the spring. After you have wound the spring, it is important to lubricate it. This will help to prevent the spring from rusting and will also make it easier to wind in the future.

To lubricate the spring, you can use a light oil or a spray lubricant. Apply the lubricant to the entire surface of the spring.

Here is a table that summarizes the steps for winding a new tension spring:

Step	Description
1	Place the spring on the winding cone.
2	Insert the winding bar into the hole in the center of the spring.
3	Secure the winding bar in place.
4	Begin winding the spring.
5	Secure the spring.
6	Lubricate the spring.

Balancing the Garage Door with Tension Springs

If your garage door is imbalanced, it can be difficult to open and close smoothly. Tension springs are used to balance the weight of the door so that it opens and closes evenly. If the springs are not properly tensioned, the door can become unbalanced and difficult to operate.

7. Adjust the Tension

To adjust the tension on the springs, you will need to use a spring tension gauge. This tool will help you measure the tension on the springs so that you can get them set to the correct level. The tension gauge will have a hook on one end that you can attach to the spring, and a dial on the other end that will show you the tension in pounds. Once you have attached the hook to the spring, pull on the gauge until the dial shows the correct tension. The correct tension will vary depending on the type of spring and the weight of the door, so you should consult the manufacturer’s instructions for the specific tension that is required.

Once you have adjusted the tension on the springs, test the door to make sure that it is balanced. If the door is still not balanced, you may need to adjust the tension on the springs again. It may take a few tries to get the tension just right, so be patient and keep testing the door until it is balanced.

Here are some tips for tensioning garage door springs:

Always use a spring tension gauge to measure the tension on the springs.
The correct tension will vary depending on the type of spring and the weight of the door.
Be patient and keep testing the door until it is balanced.

Additional Tips

In addition to the steps outlined above, here are some additional tips for tensioning garage door springs:

If you are not comfortable working with springs, you should hire a professional to tension them for you.
When tensioning springs, always wear safety glasses and gloves.
Never exceed the manufacturer’s recommended tension for the springs.

Adjusting Tension for Proper Operation

The correct tension is crucial for the smooth and safe operation of your garage door. If the tension is too loose, the door may not open or close properly, while too much tension can strain the springs and other components.

8. Checking and Adjusting Tension

To check the tension, lift the garage door manually about halfway. It should remain in place without falling or rising. If it falls, the tension is too low. If it rises, the tension is too high.

To adjust the tension, refer to the spring manufacturer’s instructions or follow these general steps:

Spring Type	Adjustment
Torsion Spring	Adjust the bolts on the spring shaft to increase or decrease tension.
Extension Spring	Adjust the bolts on the mounting brackets to increase or decrease tension.

Make small adjustments and test the door’s operation after each adjustment until the desired tension is achieved. Remember to tighten any bolts or nuts securely to ensure the tension remains consistent.

Safety Precautions

Prior to servicing your garage door springs, ensure the following precautions are observed:

Wear proper safety gear, including gloves and safety glasses.
Fully disconnect the garage door opener from the power supply.
Secure the garage door in the closed position using a c-clamp or locking pliers.
Never attempt to move or balance the door manually without first relieving tension from the springs.

Maintenance Tips

To ensure optimal performance and extend the lifespan of your garage door springs, adhere to the following maintenance tips:

Regularly lubricate the springs with a silicone-based lubricant.
Inspect the springs for signs of wear or damage, such as rust or cracks.
Replace springs that exhibit significant wear or damage immediately.
Consider having a professional garage door technician inspect and service your springs annually.

Wind the Torsion Spring

Tensioning a torsion spring requires precise calculation and proper equipment. To ensure safety and accuracy, follow these detailed steps:

Calculate the required spring tension: Determine the correct tension based on the door weight, height, and spring type. Refer to the spring manufacturer’s specifications.
Gather necessary tools: You will need a winding bar, tension gauge, safety glasses, and gloves.
Secure the spring: Ensure the spring is safely mounted on the shaft and the winding bar is securely attached to the spring.
Connect the tension gauge: Attach the tension gauge to the winding bar to monitor the spring tension.
Begin winding: Slowly and carefully wind the spring by turning the winding bar in the appropriate direction, either clockwise or counterclockwise, as per the manufacturer’s instructions.
Monitor the tension: Regularly check the tension gauge to ensure the desired tension is achieved.
Tighten the set screws: Once the correct tension is reached, tighten the set screws on the winding bar to lock the spring in place.
Safety check: Before releasing the door, carefully inspect the spring and connections to ensure they are secure.
Release the door: Gradually release the c-clamp or pliers that were securing the door, allowing the springs to balance the door.

Lubrication Schedule

To ensure smooth operation and prevent premature wear, follow this recommended lubrication schedule for your garage door springs:

Spring Type	Lubrication Frequency
Torsion Springs	Every 6-12 months
Extension Springs	Every 3-6 months

1. Visual Inspection:

Begin by inspecting both springs for visible damage like cracks, rust, or broken coils. These signs indicate the need for replacement.

2. Balance Test:

Disconnect the opener and manually lift the door about halfway. If the door stays in place, the springs are properly tensioned. If it falls or rises, adjustment is required.

3. Spring Type Determination:

Identify the type of springs used in your door (torsion or extension) and locate the tension adjustment bolts or pulleys.

4. Calculation of Spring Tension:

To calculate the desired tension, refer to the manufacturer’s guidelines or consult a professional. It varies depending on door weight, size, and spring type.

5. Loosening Tension:

For torsion springs, use a ½-inch socket wrench to loosen the adjustment bolts on both ends of the shaft. For extension springs, disengage the hook from the bracket and slide it down.

6. Increasing Tension:

Tighten the adjustment bolts on torsion springs or slide the hook up on extension springs to increase tension.

7. Safety Precautions:

Always wear gloves and safety glasses during spring adjustment. Release the tension slowly and never exceed the recommended tension.

8. Reattachment:

Once the desired tension is achieved, reattach the opener, and reconnect the spring to the door.

Troubleshooting Common Spring-Related Issues

9. Binding Springs:

If the springs bind or squeal during operation, it indicates excessive tension. Loosen the bolts or slide the hook down slightly.

10. Broken Springs:

Broken springs present a significant safety hazard. Remove tension from the springs, replace them immediately, and contact a professional for installation. Ignoring broken springs can lead to severe injuries or damage to the door.

How to Tension a Garage Door Spring

Tensioning a garage door spring requires caution and proper technique. Follow these steps carefully:

1. Unplug the Garage Door Opener: Safety first! Disconnect the power source from the garage door opener to prevent accidental operation while adjusting the spring.

2. Secure the Door: Using a sturdy object (e.g., a wood block), wedge it under the bottom of the door to hold it in place and prevent it from falling.

3. Identify the Type of Spring: Determine whether you have extension springs (located above the door) or torsion springs (horizontal, above the door opening).

4. Adjust the Spring: Use a winding bar to carefully adjust the spring tension. For extension springs, turn the winding bar to wind or unwind the spring (follow the designated winding direction). For torsion springs, insert the winding bar into the center hole and turn it to tighten or loosen the spring.

5. Count the Turns: As you adjust the spring, keep track of the number of turns made. This will help you return to the original setting if needed.

6. Check the Balance: After adjusting the spring, release the door and observe its movement. It should open and close smoothly, without binding or sagging.

7. Fine-Tune the Tension: If necessary, make small adjustments to the spring tension until the door operates optimally.