Threading a Necchi sewing machine can be a daunting task for beginners. However, with the right guidance and a few simple steps, you can master this essential skill and embark on your sewing journey with confidence. As you delve into the intricacies of threading, remember that patience and precision are key.
Before you begin, gather all the necessary materials. You will need a spool of thread, a needle, and your Necchi sewing machine. Ensure that the machine is turned off and unplugged for safety. Next, locate the thread path on your machine. This typically consists of a series of guides and tension discs that direct the thread from the spool to the needle. Follow the thread path carefully, threading the upper tension disc first, then the lower tension disc, and finally the needle.
Once the upper thread is in place, you need to thread the bobbin. Open the bobbin case and insert the bobbin, ensuring that the thread unwinds in a clockwise direction. Then, draw the thread up through the bobbin case tension spring and guide it through the small hole in the bobbin case. Finally, pull the thread back down into the bobbin case and trim any excess. With both the upper and lower threads in place, you are ready to start sewing. Congratulations! You have successfully threaded your Necchi sewing machine.
Preparing the Machine for Threading
Before you begin threading your Necchi sewing machine, it’s crucial to ensure it’s properly prepared to receive the thread. Here are the detailed steps to follow:
1. Raise the Needle and Presser Foot
Begin by turning the handwheel towards you until the needle reaches its highest position. This will create ample space for the thread to pass through the machine. Next, lift the presser foot by pulling the lever located at the back of the machine. This will disengage the presser foot from the fabric, allowing you to thread it.
2. Open the Bobbin Case and Thread the Bobbin
Locate the bobbin case, which is typically situated underneath the needle plate. Open it by sliding the latch towards the side. Insert an empty bobbin onto the bobbin winder and wind the thread onto it, ensuring it rotates clockwise. Once the bobbin is full, cut the thread and place the bobbin into the bobbin case.
3. Thread the Upper Thread Guide
With the bobbin in place, bring the thread from the spool to the upper thread guide, which is located at the top of the machine. Follow the arrows or instructions marked on the machine to guide the thread through the various guide points.
4. Thread the Tension Discs
Locate the tension discs, which are usually right above the needle bar. Pass the thread between the tension discs following the marked route. Adjust the tension knob to your desired thread tension.
5. Thread the Needle
Hold the thread and use the needle threader, if available, or thread the needle manually. Insert the thread through the eye of the needle from front to back.
6. Pull Up the Bobbin Thread
Hold the end of the thread tail from the bobbin case and gently pull it up. The needle thread and bobbin thread should now be hooked together and form a loop.
With the machine properly prepared, you can now proceed to threading the machine and begin sewing. Remember to adjust the thread tension and stitch settings according to the fabric you are working with.
Setting the Thread Path on the Spool Pin
The spool pin is a post located on the right-hand side of the machine. It is used to hold the spool of thread and prevent it from slipping or falling.
To set the thread path on the spool pin, follow these steps:
- Place the spool of thread on the spool pin. Ensure that the thread is unwinding clockwise from the spool.
-
Guide the thread through the tension discs by following the arrow marked on the discs. Tension discs control the tightness of the stitches.
- Most sewing machines have two tension discs. The upper one is fixed, while the lower one is movable.
- Position the thread between the two tension discs and adjust the lower disc to the desired tension setting.
- The tension setting depends on the type of thread and fabric being used. Generally, a higher tension setting is required for thicker fabrics and threads.
- After adjusting the tension, ensure the thread is securely held by both discs.
- Draw the thread down and around the thread guide located to the left of the spool pin. This guide helps keep the thread in place and prevents it from tangling.
- Pass the thread through the thread take-up lever, which is a metal arm that moves up and down as the machine sews. The take-up lever helps to control the flow of thread onto the needle.
- Pull the bobbin thread up through the hole in the needle plate.
- Hold the bobbin thread in your left hand and the upper thread in your right hand.
- Pass the upper thread through the left-hand slot in the thread guide.
- Wrap the upper thread around the top of the thread guide.
- Pull the upper thread through the right-hand slot in the thread guide.
- Thread the upper thread through the eye of the needle.
-
Hold the thread in your left hand, with the needle dangling below.
-
With your right hand, guide the thread up and over the top of the take-up lever, from right to left.
-
Bring the thread down the back of the lever and hook it onto the small notch or hook at the bottom.
-
Gently pull on the thread to ensure it’s securely hooked.
-
Hold the thread taut with your left hand as you release the take-up lever.
-
Check that the thread is moving smoothly and without any resistance as the take-up lever rises and falls.
- Press the foot pedal to start the machine.
- Hold the end of the thread and guide it onto the bobbin.
- Once the thread is wound onto the bobbin, cut the thread and remove the bobbin from the spindle.
- Insert an empty bobbin onto the spindle of the bobbin winder.
- Pass the thread through the thread guide on the bobbin winder.
- Flip the bobbin winder arm to engage it.
- Depress the foot pedal or press the start button.
- Allow the machine to wind the thread onto the bobbin until it fills up.
- Release the foot pedal or press the stop button.
- Flip the bobbin winder arm back to disengage it.
- Remove the full bobbin from the spindle.
- Check the tension of the thread on the bobbin by pulling gently. If it’s too loose or too tight, adjust the tension screw on the bobbin winder.
- Cut a small piece of thread from the bobbin, allowing some excess for threading the machine.
- Store the bobbin in its designated compartment in the sewing machine.
- Open the bobbin cover by pressing the latch.
- Insert the bobbin into the bobbin case, ensuring that the thread is unwinding in a clockwise direction.
- Pull the thread through the small hole in the bobbin case.
- Gently pull the thread up into the bobbin tension spring, which is located on the top of the bobbin case.
- Pull the thread through the thread guide on the side of the bobbin case.
- Pull the thread up through the center of the hole in the bobbin case.
- Pull the thread down through the other hole in the bobbin case.
- Pull the thread through the thread guide that is located on the bottom of the bobbin case.
- Pull the thread up through the hole in the bobbin case that is closest to the needle.
- Pull the thread through the other hole in the bobbin case that is closest to the needle.
- Raise the presser foot and the needle to their highest position.
- Locate the spool pin on the top of the machine.
- Place the spool of thread onto the spool pin and draw the thread through the thread guide.
- Bring the thread down to the tension discs and through the thread guide.
- Thread the needle from front to back.
- Pull about 6 inches of thread through the needle and under the presser foot.
- Lower the needle and the presser foot.
- Start sewing!
| Tension Setting | Description |
|---|---|
| Low | For delicate fabrics and fine threads |
| Medium | For most general-purpose fabrics and threads |
| High | For heavy fabrics and thick threads |
Guiding the Thread Through the Upper Tension Discs
Step 1: Lift the Thread Guide and Disc Plate
Locate the thread guide and disc plate situated at the top of the machine. Gently lift these components to open up the threading path.
Step 2: Position the Thread Through the Disc Guide
Direct the thread from the spool into the small groove located on the disc guide. Ensure that the thread is fully seated in the guide to prevent slipping or jamming.
Step 3: Pass the Thread Around the Upper Tension Discs
From the disc guide, the thread needs to be guided around the upper tension discs.
Start by passing the thread behind the right-hand tension disc. Then, bring it over and around the left-hand disc, ensuring that it goes between the two washers underneath.
Next, guide the thread back up and over the right-hand disc again. Finally, draw it down and out to the left, passing it through the hole in the tension guide.
Here’s a detailed breakdown of the steps in a table format:
| Step | Action |
|---|---|
| 1 | Pass thread behind the right-hand tension disc. |
| 2 | Bring thread over and around the left-hand disc, between the washers. |
| 3 | Guide thread back up and over the right-hand disc. |
| 4 | Draw thread down and out to the left, through the tension guide hole. |
Inserting the Thread into the Needle Bar
Before you begin, make sure that the needle is in the up position. To do this, turn the handwheel towards you until the needle is at its highest point.
Now, take the thread and pass it through the first hole in the needle bar, from front to back. Then, pull the thread down and pass it through the second hole, from back to front.
Next, take the thread and pass it under the tension disc. There are usually two tension discs on a Necchi sewing machine, one for the upper thread and one for the lower thread. Make sure that you pass the thread under the correct disc.
Finally, pull the thread down and pass it through the take-up lever. The take-up lever is the part of the machine that moves the thread up and down as you sew. Make sure that the thread is passed through the take-up lever in the correct direction.
Once the thread is passed through the take-up lever, you can begin sewing. To do this, simply turn the handwheel towards you and start sewing.
Thread Path Diagram
The following diagram shows the path of the thread through the needle bar:
| Thread Path |
|---|
| Thread passes through the first hole in the needle bar, from front to back. |
| Thread passes through the second hole in the needle bar, from back to front. |
| Thread passes under the tension disc. |
| Thread passes through the take-up lever. |
Passing the Thread Through the Thread Guide
To pass the thread through the thread guide, follow these steps:
The thread guide is designed to help keep the thread taut and prevent it from tangling. Be sure to thread the thread through the thread guide in the correct order as shown in the diagram below:
| Step | Image |
|---|---|
| 1 |  |
| 2 |  |
| 3 |  |
| 4 |  |
| 5 |  |
| 6 |  |
Hooking the Thread onto the Take-Up Lever
6. **Hooking the Thread onto the Take-Up Lever**: This step involves guiding the thread around the take-up lever, which is a small, U-shaped arm that moves up and down as you sew. To do this:
Troubleshooting Tips
If you experience any difficulties hooking the thread onto the take-up lever, try the following:
| Issue | Solution |
|---|---|
| Thread is slipping off the hook | Ensure the thread is securely hooked onto the notch and pull it taut. |
| Thread is not moving smoothly | Check if the lever is obstructed. Clean or adjust as needed. |
| Needle is not threading properly | Rewind the thread spool and try again. Replace the needle if necessary. |
Threading the Bobbin Winder
To thread the bobbin winder, follow these steps:
1. Locate the bobbin winder on the machine.
It is typically located on the top right side of the machine.
2. Raise the bobbin winder spindle.
This will allow you to place the bobbin on the spindle.
3. Place the bobbin on the spindle.
Make sure that the bobbin is facing the correct way. The thread should come off the bobbin from the outside.
4. Bring the thread through the thread guide.
The thread guide is located on the top of the bobbin winder.
5. Bring the thread through the tension disc.
The tension disc is located on the bottom of the bobbin winder.
6. Bring the thread through the second thread guide.
The second thread guide is located on the top of the bobbin winder spindle.
7. Wind the thread onto the bobbin.
To wind the thread onto the bobbin, follow these steps:
| Troubleshooting Tips |
|---|
| If the thread is not winding evenly, adjust the tension disc. |
| If the thread is breaking, check the thread guide and tension disc for any burrs or sharp edges. |
| If the bobbin is not winding properly, make sure that it is facing the correct way on the spindle. |
Winding the Bobbin
To wind the bobbin, follow these detailed steps:
1. Prepare the Bobbin
2. Thread the Machine
3. Engage the Bobbin Winder
4. Start Winding
5. Wind the Thread
6. Stop Winding
7. Remove the Bobbin
8. Inspect and Prepare the Thread
| Bobbin Winding Troubleshooting | ||
|---|---|---|
| Problem | Cause | Solution |
| Bobbin thread tangles | Uneven tension | Adjust tension screw on bobbin winder |
| Bobbin doesn’t fill evenly | Thread guide misaligned | Properly align thread guide |
Inserting the Bobbin into the Bobbin Case
Locate the bobbin winder on the side of the machine. Insert an empty bobbin onto the winder spindle. Wind the thread clockwise around the bobbin, leaving about 2 inches of thread at the end.
Hold the bobbin case in your hand with the latch facing you. Insert the bobbin into the case, making sure that the thread is unwinding from the top of the bobbin.
Pull the thread through the slot in the top of the bobbin case. Wind the thread around the tension disc, then thread it through the guide on the left side of the case.
Bring the thread back up through the slot in the top of the bobbin case. Pull the thread until there is about 6 inches of slack.
Close the latch on the bobbin case. Insert the bobbin case into the machine.
Positioning the Bobbin Thread
Locate the bobbin thread pickup lever on the right side of the machine. Raise the lever to the up position. Use a needle or tweezers to lift the bobbin thread up and over the pickup lever.
Lower the bobbin thread pickup lever. Hold the bobbin thread taut, and turn the handwheel towards you until you feel the bobbin thread being pulled into the machine.
Continue turning the handwheel until the bobbin thread appears in the needle hole.
Bobbin Tension Adjustment
Adjust the bobbin tension by turning the screw on the bobbin case. Turning the screw clockwise increases tension; turning it counterclockwise decreases tension.
| Bobbin Tension Setting | Result |
|---|---|
| Too Tight | Thread will break |
| Too Loose | Stitches will be loose and uneven |
| Correct | Thread will be slightly loose, but will not break |
Drawing Up the Bobbin Thread
To draw up the bobbin thread, follow these steps:
| Step | Description |
|---|---|
| 1 | Open the bobbin cover by pressing the latch. |
| 2 | Insert the bobbin into the bobbin case, ensuring that the thread is unwinding in a clockwise direction. |
| 3 | Pull the thread through the small hole in the bobbin case. |
| 4 | Gently pull the thread up into the bobbin tension spring, which is located on the top of the bobbin case. |
| 5 | Pull the thread through the thread guide on the side of the bobbin case. |
| 6 | Pull the thread up through the center of the hole in the bobbin case. |
| 7 | Pull the thread down through the other hole in the bobbin case. |
| 8 | Pull the thread through the thread guide that is located on the bottom of the bobbin case. |
| 9 | Pull the thread up through the hole in the bobbin case that is closest to the needle. |
| 10 | Pull the thread through the other hole in the bobbin case that is closest to the needle. |
How To Thread A Necchi
Threading a Necchi sewing machine is a simple process that can be completed in just a few steps. Here are the instructions on how to thread a Necchi:
People Also Ask About How To Thread A Necchi
How do I adjust the tension on my Necchi sewing machine?
The tension on a Necchi sewing machine can be adjusted by turning the tension dial. The tension dial is located on the top of the machine, and it is usually marked with numbers from 0 to 9. A higher number indicates a tighter tension, and a lower number indicates a looser tension.
How do I change the needle on my Necchi sewing machine?
To change the needle on a Necchi sewing machine, first raise the presser foot and the needle to their highest position. Then, use a small screwdriver to loosen the screw that holds the needle in place. Once the screw is loose, you can pull the needle out of the machine. To insert a new needle, simply insert it into the hole in the needle bar and tighten the screw.
